Yaskawa GPD515/G5 - Manual (Page 39)

10 Appendix 2 Parameter Cross Reference
YASKAWA PL.A1000.01 G5 to A1000 - Product Transition Guide 39
Operation Mode
Selection
Reference Selection b1-01 1 b1-01 1
b1-01 b1-01
0: Operator 0: Operator
1: Control circuit terminal
(analog input) 1: Control circuit terminal
(analog input)
2: Serial Communication 2: MEMOBUS comm.
3: Option PCB 3: Option PCB
4: EWS 4: Pulse train input
Operation Method
Selection
b1-02 1 b1-02 1
b1-02 b1-02
0: Operator 0: Operator
1: Control circuit terminal 1: Control circuit terminal
2: Serial Communication 2: MEMOBUS comm.
3: Option PCB 3: Option PCB
4: EWS Not available
Stopping Method
Selection
b1-03 0 b1-03 0
b1-03 b1-03
0: Ramp to stop 0: Ramp to stop
1: Coast to stop 1: Coast to stop
2: DC Injection Braking 2: DC Injection Braking
3: Coast to stop with timer 3: Coast to stop with timer
Prohibition of Reverse
Operation
b1-04 0 b1-04 0
b1-04 b1-04
0: Reverse possible 0: Reverse possible
1: Reverse prohibited 1: Reverse prohibited
Operation Selection for
setting of E1-09 or
Less
b1-05 0 b1-05 0
b1-05 b1-05
0: Run at frequency reference 0: Run at frequency reference
1: Shut off drive output 1: Shut off drive output
2: Operate by E1-09 2: Operate by E1-09
3: Zero speed 3: Zero speed
Read sequence input
twice
b1-06 1 b1-06 1
b1-06 b1-06
0: 2 ms - 2 scans 0: 1 ms - 1 scan
1: 5 ms - 2 scans 1: 1 ms - 2 scans
Operation Selection
After Switching to
Remote Mode
b1-07 0 b1-07 0
b1-07 b1-07
0: Cycle Run command 0: Cycle Run command
1: Accept external Run cmd 1: Accept external Run cmd
Run Command
Selection in PRG
Mode
b1-08 0 b1-08 0
b1-08 b1-08
0: Disabled. 0: Disabled.
1: Run cmd always accepted 1: Run cmd always accepted
― 2: Cannot enter Program Mode
Run Command at
Power Up
─ ─ b1-17 0
0: Prohibited
1: Allowed
Change b1-17 to 1.
DC Injection Braking
Zero speed level (DC
injection braking
starting frequency)
b2-01 0.5 Hz b2-01 0.5 Hz ―
DC Injection Braking
current
b2-02 50 % b2-02 50 % ―
DC Injection Braking
Time at Start
b2-03 0.00 s b2-03 0.00 s ―
DC Injection Braking
Time at Stop
b2-04 0.00 s b2-04 0.50 s* *Determined by the control mode selected.
Magnetic Flux
Compensation volume
b2-08 0 % b2-08 0 % ―
Speed Search
Speed Search Selection
at start
b3-01 0* b3-01 0*
b3-01 b3-01
0: Disabled 0: Disabled
1: Enabled 1: Enabled
*Default value changes according to the control mode.
Speed Search
Operating Current
b3-02 100 %* b3-02 120 %* *Default value changes according to the control mode.
Speed Search
Speed Search
Deceleration Time
b3-03 2.0 s b3-03 2.0 s ─
Timers
Timer Function On-
Delay Time
b4-01 0.0 s b4-01 0.0 s ─
Timer Function Off-
Delay Time
b4-02 0.0 s b4-02 0.0 s ─
Parameter Name
G5 A1000 Comments (Gray shading indicates default settings)
No. Default No. Default G5 A1000