Comtech EF Data CDM-625A - Manual (Page 374)

CDM-625A Advanced Satellite Modem MN-CDM625A
Serial-based Remote Product Management Revision 3
8–62
Parameter
Command
(Instruction
& Qualifier)
Number of
Arguments
Description of Arguments
Response to
Command
Query
(Instruction &
Qualifier)
Response to Query
Average WAN
Buffer Fill State
N/A 2 bytes,
numeric
Query only.
Returns the value of Average WAN buffer fill state in the form xx, where:
xx=percentage value, from 00 thru 99(%).
Example: <0/WBF? >0000/WBF=33 (indicates fill state at 33%)
N/A WBF? WBF=xx
(see Description
of Arguments)
Switch MAC
Learning
SML= 1byte, 0 or 1 Command or Query.
Sets or returns Switch MAC learning in the form x, where:
0=Off
1 =On
SML=
SML?
SML*
SML#
SML? SML=x
(see Description of
Arguments)
VLAN Mode
Enable
SVM= 1 byte, 0 or 1 Command or Query.
Sets or returns VLAN Mode in the form x, where:
0=VLAN is Disabled
1=VLAN is Enabled
SVM=
SVM?
SVM*
SVM#
SVM? SVM=x
(see Description of
Arguments)
VLAN Table SVT= Up to 287 byes Command or Query.
Sets or returns all entries in the VLAN table in the form aaaabcde,aaaabcde,aaaabcde,…, where:
aaaa=VLAN ID: Value range=0001-4095, must not be duplicate of any PVID.
b=property of port 1: 0=Tagged, 1=Filtered, 2=Untagged
c=property of port 2: 0=Tagged, 1=Filtered, 2=Untagged
d=property of port 3: 0=Tagged, 1=Filtered, 2=Untagged
e=property of port 4: 0=Tagged, 1=Filtered, 2=Untagged
SVT=
SVT?
SVT*
SVT#
SVT? SVT=aaaabcde,aaaab
cde,aaaabcde…
(see Description of
Arguments)
Add entry to
VLAN table
SVA= 8 bytes Command only.
Adds entry to VLAN table in the form aaaabcde, where:
aaaa=New VLAN ID: Value range=0001-4095, must not be duplicate of any PVID or VLAN ID existing in VLAN table.
b=property of port 1: 0=Tagged, 1=Filtered, 2=Untagged
c=property of port 2: 0=Tagged, 1=Filtered, 2=Untagged
d=property of port 3: 0=Tagged, 1=Filtered, 2=Untagged
e=property of port 4: 0=Tagged, 1=Filtered, 2=Untagged
SVA=
SVA?
SVA*
SVA#
N/A SVA=aaaabcde
(see Description of
Arguments)
Management
VLAN ID
SMV= 4 bytes,
numeric
Command or Query.
Sets or returns the Management Port’s VLAN ID in the form aaaa, where:
aaaa=the VLAN ID number in the range 0001-4095.
SMV=
SMV?
SMV*
SMV#
SMV? SMV=aaaa
(see Description of
Arguments)
Delete entry in
VLAN table
SVD= 4 bytes,
numeric
Command only.
Deletes VLAN table entry in the form aaaa, where:
aaaa=the VLAN ID number in the range 0001-4095.
SVD=
SVD?
SVD*
SVD#
N/A SVD=aaaa
(see Description of
Arguments)
Packet
Processor Card
Enable
PPE= 1 byte, 0 or 1 Command or Query.
Sets or returns Packet Processor Card operation in the form x, where:
0=Packet Processor Card is Disabled
1=Packet Processor Card is Enabled
Note: Change of this configuration results in modem auto-reboot only when IP Packet Processor option card is installed
and enabled. Otherwise, when the IP Packet Processor option card is not installed, this selection is stored but is otherwise
non-functional.
PPE=
PPE?
PPE*
PPE#
PPE? PPE=x
(see Description of
Arguments)