Reznor R6GN Option - Installation - High Static Blower Drive - Light Commercial - Manual (Page 27)

27
R4GM & R6GN-150* Series HSD kits:
918799 (208-230V, 3Ø, 60 Hz)
920637 (460V, 3Ø, 60 Hz)
Blower Performance Chart ‡ Indicates Factory Sheave Setting for Pre-confi gured Units
External
Unit Static
(in-Wg)
Operating @
230 or 460
Volts
Adjustable Motor Sheave Setting
Fully
Closed
1/2 Turn
Open
1 Turn
Open
1.5 Turns
Open
2.0 Turns
Open
2.5 Turns
Open
3.0 Turns
Open
3.5 Turns
Open
4.0 Turns
Open ‡
4.5 Turns
Open
5.0 Turns
Open
5.5 Turns
Open
6.0 Turns
Open
0.9
CFM
RPM
kW
1.0
CFM
RPM
kW
1.1
CFM 5350 5100 4850
RPM 1188 1168 1148
kW 3.20 2.98 2.75
1.2
CFM 5225 5000 4700 4400
RPM 1210 1189 1169 1148
kW 3.23 3.00 2.75 2.50
1.3
CFM 5100 4850 4600 4250 3900
RPM 1231 1211 1190 1170 1149
kW 3.25 3.00 2.75 2.53 2.30
1.4
CFM 5300 5050 4800 4500 4200
RPM 1271 1252 1232 1212 1191
kW 3.55 3.33 3.10 2.85 2.60
1.5
CFM 5400 5150 4900 4650 4400 4050 3700
RPM 1313 1293 1273 1253 1233 1213 1192
kW 3.80 3.55 3.30 3.09 2.87 2.59 2.30
1.6
CFM 5375 5000 4725 4450 4175 3900 3600
RPM 1334 1314 1295 1275 1255 1235 1214
kW 3.90 3.60 3.35 3.10 2.86 2.62 2.35
1.7
CFM 5350 4925 4500 4250 4000
RPM 1355 1336 1316 1296 1276
kW 4.00 3.70 3.40 3.15 2.90
1.8
CFM 4850 4475 4100 3725
RPM 1357 1338 1318 1297
kW 3.75 3.48 3.20 2.95
1.9
CFM 4400 4000 3600
RPM 1359 1340 1320
kW 3.50 3.23 2.95
2.0
CFM
RPM
kW
Values include losses for: Unit Casing, 2” Disposable Filters, Dry Evaporator Coil & Installed Heat Exchanger
Values shown refl ect operation at 230V or 460V. For operation at 208V, deduct 0.025 from unit static.
3862
Indicates a recommended unit operational point 1159
3.03
3493
Indicates an allowable setting that is not recommended for unit operation †
† These operational points should be carefully examined by the installer for proper unit setup and heater operation if used.
1017
2.07
Indicates a setting that is not permitted for unit operation
Table 23. Blower Performance for R4GM & R6GN-150* Units
(15 Ton Models Only)