Great Planes Learjet 40 Kit - GPMA0439 - Manual (Page 4)

D Tricycle retract gear - (HCAP4000)
D Retract servo (Futaba S136G or similar)
D Standard servo for nose gear retract
D Servo "Y" harness
D 1-1/4" x 5/32" Wheel axles (3) (GPMQ4280)
D 2-56 x 12" Threaded wire pushrods (2) (GPMQ3750)
D 2-56 x 36" Threaded wire pushrods (1) (GPMQ3716)
D Screw-Lock pushrod connector (3) (GPMQ3870)
D 4-40 x 1/8" Set screws
*ltems in parentheses (GPMQ1234) are suggested part
numbers recognized by distributors and hobby shops and
are listed for your convenience GPM is the Great Planes
brand, HCA is the Hobbico® brand, TOP is Top Flite
On our workbench, we have four 11" Easy-Touch Bar
Sanders, equipped with #50, #80, #150 and #220-gnt
sandpaper This setup is all that is required for almost
any sanding task Custom sanding blocks can be made
from balsa for sanding hard to reach spots We also keep
some #320-gnt wet-or-dry sandpaper handy for finish
sanding before covering
D Hand or electric drill *
D Drill bits 1/16", 3/32", 7/64" or #35, 1/8", #29 or
9/64", 3/16", #10 or 13/64", 15/64", 17/64" and 1/4"
D Sealing iron - (TOPR2100)
D Hot sock (optional) - (TOPR2175)
D Heat gun (optional) - (TOPR2000)
D Razor saw
D #1 knife handle - (XACR4305)
D #11 Blades - (HCAR0311 pkg of 100)
D Common and needle nose pliers
D Screwdrivers (phillips and flat)
D T-Pins - (HCAR5100 small, HCAR5150 medium,
HCAR5200 large)
D Straightedge - (Fourmost Non Slip FORR2149)
D Masking tape
D Sandpaper (coarse, medium, fine grit)
D Sanding blocks or Great Planes Easy-Touch"
Bar Sander (GPMR6170 -11" & GPMR6172 - 22")
D Waxed paper
D Lightweight balsa filler - (HCAR3401)
D 5/32" brass tube (optional)
D 1/8" brass tube (optional)
D Tap wrench
D 1/4-20 Tap - (GPMR8105 w/dnll bit)
D IsopropyI rubbing alcohol (70%)
D Dremel® Moto Tool® or similar w/sanding drum and
cutting burr (optional)
D Kyosho" curved scissors (optional) - (KYOR1010)
Great Planes Easy-Touch Bar Sanders are made from
light-weight extruded aluminum and can be found at
most hobby shops The sanders are available in two
sizes - 11" (GPMR6170) for most general purpose
sanding and 22" (GPMR6172) for long surfaces such as
wing leading edges We recommend using the 2-1/4"
wide self adhesive sandpaper sold in 12' rolls by Great
Planes The sandpaper is available in three different grit
sizes - #80-grit (GPMR6180), #150-grit (GPMR6183)
and #220-grit (GPMR6185) Standard sandpaper can be
attached by gluing it to the sander with rubber cement.
Apply the rubber cement to both the bottom of the sander
and the back of the sandpaper When both surfaces are
dry to the touch, press the sandpaper firmly onto the
sander Spray adhesive can be used for this purpose but
it's much harder to remove the sandpaper when you
need to replace it Use a knife blade for cutting
sandpaper, not your good scissors!
Balsa Basswood Plywood
Elev = Elevator Fuse = Fuselage
LG = Landing Gear
Ply = Plywood
Stab = Stabilizer
" = Inches
LE = Leading Edge (front)
Lt = Left
Rt = Right
TE = Trailing Edge (rear)
4