Waterworks Regulator Gooseneck Single Spout Kitchen Faucet, Metal Wheel Handle and Spray - Manual (Page 2)

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
REGULATOR
Gooseneck Single Spout Kitchen Faucet Installation Guidelines
Page 2 of 4
Rev - 01
10.9.2014
These guidelines have been prepared for the professional contractor to aid in the installation of:
REGULATOR GOOSENECK SINGLE SPOUT KITCHEN FAUCET WITH METAL WHEEL HANDLE AND SPRAY
(STYLE No. RGKM20, RG20KM UK)
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
FIGURE – 02
4. Re-install the RUBBER WASHER, METAL WASHER and
NUT onto the SHANK and securely tighten the NUT to
secure the TEMPERATURE VALVE BODY to the
mounting surface.
5. Insert the TUBE into the TEMPRATURE VALVE BODY,
making sure the O-RING, METAL WASHER, and NUT
are attached properly. Do
NOT tighten the NUT. The
flanged end of the TUBE must be on the outside. See
FIGURE – 03.
NOTE:
a. Depending on the desired location of the SPOUT,
the NUT and COVER may need to be removed
from TEMPERATURE VALVE BODY and installed
on the opposite side.
b. The TUBE is aesthetic only and does NOT hold or
carry water. The TUBE can be cut to accommodate
different on-center spreads. The max on-center
spread is 12” [305mm].
FIGURE - 03
METAL WASHER
RUBBER WASHER
NUT
HOUSING
HOSE "BLUE"
HOSE "RED"
TEE
HOSE "GREEN"
ESCUTCHEON
VALVE BODY
METAL WASHER
RUBBER WASHER
NUT
HOUSING
HOSE "BLUE"
HOSE "RED"
TEE
HOSE "GREEN"
ESCUTCHEON
VALVE BODY
NUT
COVER
O-RING
METAL
WASHER
NUT
"TUBE MUST BE ON THE
SAME SIDE AS THE
SPOUT MOUNTING
HOLE"
TUBE
NUT
"DO NOT CUT
FLANGED END"
NUT
COVER
O-RING
METAL
WASHER
NUT
"TUBE MUST BE ON THE
SAME SIDE AS THE
SPOUT MOUNTING
HOLE"
TUBE
NUT
"DO NOT CUT
FLANGED END"
SPOUT(S) INSTALLATION:

The SPOUT only has a volume/on/off control function.
6. Remove the NUT, METAL WASHER, and RUBBER
WASHER from the SHANK. See FIGURE - 04. Do NOT
remove the O-RING beneath the ESCUTCHEON.
FIGURE - 04
7. Ensure that the HOSES are securely tightened to the
SPOUT, then insert the SHANK through the Ø1-3/4”
[44mm] hole on the mounting surface making sure
the O-RING is beneath the ESCUTCHEON.
NOTE: The HOSES are marked with colored ZIP TIES
to identify their function,
Green for incoming mixed
water and yellow for outgoing diverted water.
8. Ensure that the flanged end of the TUBE sits flush
with the SPOUT VALVE BODY. See FIGURE - 05.
Thread and tighten both NUTS on the TUBE.
CAUTION
: The TUBES can be cut if necessary, adjust
as needed. Do NOT cut the flanged end.
FIGURE – 05
NUT
METAL WASHER
RUBBER WASHER
HOSE "YELLOW"
HOSE "GREEN"
SHANK
ESCUTCHEON
NUT
METAL WASHER
RUBBER WASHER
HOSE "YELLOW"
HOSE "GREEN"
SHANK
ESCUTCHEON
"FLANGE OF TUBE AND
SPOUT VALVE BODY
MUST BE FLUSH
"FLANGE OF TUBE AND
SPOUT VALVE BODY
MUST BE FLUSH