Waterworks Opus Low Profile Three Hole Deck Mounted Lavatory Faucet with Crystal Egg Handles - Manual

Opus Lavator y Faucet With Egg Cr ystal Handle
11/02 W A T E R W O R K S

These guidelines have been prepared for the professional contractor to aid in the installation of:
OPUS LAVATORY FAUCET WITH EGG CRYSTAL HANDLE (OPLS02-K)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
Figure 1
Valve Body
Gasket
Metal Washer
Plastic Spacer
Handle Trim Connector
Locking Nut
Handle Fixing Cap
Basin Nut
Escutcheon
Stopper Assembly
Upper Collar
Upper Gasket
Lower Gasket
Lower Drain Body
Tailpiece Gasket
Tailpiece
Pivot Rod
Knurled Nut
Figure 2
5 3 ⁄ 4 "
6 1 ⁄ 4 "
1 3 ⁄ 8 "
3 3 ⁄ 8 "
12" max.
1 3 ⁄ 8 "
3 1 ⁄ 8 "
3"
max.
2 3 ⁄ 8 "
ø2 3 ⁄ 8 "
2 5 ⁄ 16 "
max.
1 3 ⁄ 4 "
8"-12"
Note:
• Drilling hole size: 1
3 ⁄ 8 "
• Basin nuts supplied
NOTES
➢ Use only a protected, smooth-jawed, or strap wrench on any finished
surface.
➢ If possible, install this faucet assembly on the lavatory before setting.
➢ DO NOT use putty on deck fittings. Upper gaskets are provided.
INSTALLATION
➢ To remove the handle trim from the handle trim connector, unscrew the
escutcheon and pull off the handle and escutcheon together.Then,
unscrew and lift off handle trim connector. Leave locking nut, gaskets, and
plastic spacer in place on the valve body (see fig.1).
➢ Insert the valve body through the mounting hole, using the plastic spacer
(used for deck surfaces less than 1 1 ⁄ 2 " thick) if needed.Then, screw the
handle trim connector onto the valve body until fully seated. Next, tighten
the bottom locking nut to secure the valve to the deck. Repeat for the
other valve assembly. (see fig. 1)
➢ Re-attach the handle trims to the handle trim connector.
➢ Unscrew the locking barrel nuts at the base of the spout to release the
mounting plate and gasket.Then, insert the spout through the mounting
hole and secure by re-attaching and tightening the locking barrel nuts.
➢ Install the flexible supply hoses between the valve bodies and the spout
assembly.
INSTALLING THE POP-UP DRAIN (SEE FIG.2)
➢ Remove the upper collar from the pop-up drain assembly and discard the
upper gasket.
➢ Set the upper collar in the lavatory drain opening using a clear adhesive
silicone.
➢ Re-attach the lower drain assembly using the gasket provided.Tighten until
fully secured and the side connector is facing towards the wall (A clear
adhesive silicone may be used to ensure a water-tight seal between the
gasket and the lavatory).
➢ Remove the knurled nut from the side connection of lower drain
assembly.Then insert the horizontal pivot rod and re-attach the knurled
nut.
➢ Insert vertical lift rod through the spout assembly and connect to the
horizontal pivot rod, using the linkage provided (if necessary, the rods may
be field cut).
➢ To adjust the height of the drain stopper turn the adjustment screw at the
base of the stopper and tighten the locking nut upward to secure.
➢ Attach the flanged tailpiece to the lower drain assembly using the gasket
provided.Then the tailpiece to the p-trap.
➢ Using the basin nuts provided, attach the water supply to the hot and cold
valve bodies.
➢ Open supply valves and check all inlet valve connections for leaks.
➢ After installation, unscrew and remove the aerator assembly. Carefully
open the hot and cold valves fully to flush out any debris in the supply
lines. Now check all connections for leaks. After the lines have been
flushed , close the valves and reinstall the aerator assembly.
➢ If further assistance is required, please contact Product Support at:
1-800-927-2120 (8AM-7PM EST).
OPLS02-K