Waterworks Formwork One Hole Low Profile Kitchen Faucet, Metal Joystick Handle and Spray - Manual

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
FORMWORK
Single Hole Kitchen Mixer with Spray
INSTALLATION GUIDELINES
Page 1 of 2 7.18.2014
These guidelines have been prepared for the professional contractor to aid in the installation of:
FORMWORK SINGLE HOLE KITCHEN FAUCET WITH SPRAY
STYLE NOS. FMKM10 & FM10KM (UK)
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
Style No. FMKM10†
SPECIFICATIONS:
Deck Thickness: 1/4" MIN - 1-1/4" MAX
(6mm MIN - 32mm MAX)
Fitting Hole Diameter Ш1-3/8" (Ш 35mm)
Inlet/Outlet Connection
Size & Type: 3/8" Compression
Connection Hoses†
Restricted Maximum Flow
Rate: 2.2gpm (8.32 L/min)
Spout Reach: 8-11/16" (221mm)
Spout Swivel: Yes
Water Pressure: 20 psi MIN - 80psi MAX
(1.4 Bar Min - 5.5 Bar Max)
Water Pressure
Recommended: 45 psi (3 Bar)
† UK Style No. FM10KM is supplied with 2 BSP Adapters,
assembly required.
IMPORTANT:
¾ To ensure this product is installed properly, you
must read and follow these guidelines.
¾ The owner/user of this product must keep this
information for future reference.
¾ Be sure your installation conforms to federal, state,
and local codes. In the State of Massachusetts, all
installations must comply with the rules and
regulations set forth within 248 CMR.
¾ This product must be installed by a professional
licensed contractor.
¾ Inspect this product to ensure you have all the parts
required for proper installation.
¾ Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
¾ The use of certain plumber's putty may stain stone
or tile surfaces.
¾ The use of certain putty may stain stone or tile
surfaces. Upper and lower washers are provided.
SPOUT INSTALLATION:
THREADED
SHANK
MOUNTING
DECK
NUT
OUTLET
HOSE
METAL
WASHER
DIVERTER
ASSEMBLY
RUBBER
WASHER
COLD SUPPLY
HOSE
RETURN
HOSE
RUBBER
GASKET
HOT
SUPPLY
HOSE
SPOUT
ASSEMBLY
AERATOR
THREADED
SHANK
MOUNTING
DECK
NUT
OUTLET
HOSE
METAL
WASHER
DIVERTER
ASSEMBLY
RUBBER
WASHER
COLD SUPPLY
HOSE
RETURN
HOSE
RUBBER
GASKET
HOT
SUPPLY
HOSE
SPOUT
ASSEMBLY
AERATOR
FIGURE - 01
¾ See Figure 1 & 2. for Steps 1-5.
1. Remove the NUT, METAL WASHER, RUBBER
WASHER from the bottom of the THREADED
SHANK.
2. Unthread DIVERTER ASSEMBLY from OUTLET
HOSE & RETURN HOSE.
3. Insert the SPOUT ASSEMBLY with the SUPPLY
HOSES, OUTLET HOSE, RETURN HOSE &
THREADED SHANK through the hole on the
mounting surface making sure the RUBBER GASKET
is underneath the spout.
4. Re-install the RUBBER WASHER, METAL WASHER &
NUT (in that order). Tighten the NUT to secure the
spout.
5. Attach the RETURN HOSE to the 1/2" port on the
DIVERTER ASSEMBLY. Attach OUTLET HOSE to the
3/8" port on the DIVERTER ASSEMBLY.
See Figure - 02.