Waterworks .25 Low Profile Three Hole Wall Mounted Lavatory Faucet with Metal Lever Handles User Manual
Installation guidelines, 25 wall mounted lavatory faucet, Sweat x
Installation Guidelines
W A T E R W O R K S
Waterworks is a registered trademark of Waterworks Inc.
04.11.07
.25 Wall Mounted Lavatory Faucet
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 WALL MOUNTED LAVATORY FAUCET WITH CROSS HANDLES (PTLS05-K &
GUSV27R) & LEVER HANDLES (PTLS06-K & GUSV25R) All dimensions are based on origin
specification and are subject to change and variation. Please consult your Design Associate for current
specifications.
PTLS05-K (Cross Handles) & GUSV27R (Rough)
2
1
2
"Ш
2
3
8
"Ш
2
3
8
"Ш
7"
1
1
4
"Ш
PTLS06-K (Lever Handles) & GUSV25R (Rough)
7"
2
3
8
"Ш
3
1
8
"
2
3
8
"Ш
2
1
2
"Ш
1
3
16
"(min)
1
9
16
"(max)
1
3
16
"(min)
1
9
16
"(max)
1
1
4
"Ø
Check countertop and sink measurements to assure
the spout projects far enough into the sink.
Inspect this product to assure you have all parts
required for proper installation.
Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
Do NOT use putty during this installation.
ROUGH IN:
Rough in Depth: 3" minimum from center of inlets to
surface of the finished wall.
1. Run
1
2
" hot and cold supply lines. The spread
between supplies is 8" on center and is NOT
adjustable.
2. Install a well supported
1
2
" sweat x
1
2
" female IPS
adapter onto each supply line.
3. Verify the supplies are secure, level, at the proper
spread of 8" and equal depths.
4. Remove the nuts (6) from the faucet body inlets then
pull out the inlet adapters (6a).
5. Slide the nuts over the inlet adapters and thread them
into the supplies. Use a 10 mm hex wrench to tighten
the adapters.
6. Align the faucet onto the supplies making sure that the
o-ring (6b) does not get pinched then tighten the nuts
to secure the faucet.
7. Thread a
1
2
" male x
1
2
" sweat adapter (23) into the
faucet body. Sweat a piece of
1
2
" copper pipe (24)
of appropriate length onto the adapter. The copper
must protrude 1" from the surface of the finished wall.
8. Verify the supplies and faucet body are secure then
turn on the supplies and check for leaks.
HANDLE INSTALLATION:
9. Thread the handle trim connector (17) then the handle
assembly (15) onto the trim sleeve (5) until it stops. If
the escutcheon (15) contacts the wall and the handle
assembly is secure, proceed to step 12.
IMPORTANT
To ensure this product is installed properly,
you must read and follow these guidelines.
The owner/user of the faucet must keep this
information for future reference.
This faucet must be on-site prior to rough in and
allows the installer to visualize the installation and
match the 8" center spread.
Be sure your installation conforms to local codes.
Refer to the specification and assembly drawings
attached. Faucet is sold partially assembled but shown
fully disassembled for illustrative and service purposes
only.
2
1
2
"
3"min.
2
1
2
"
3"min.