Waterworks Regulator Gooseneck Single Spout Kitchen Faucet, Metal Wheel Handle and Spray - Manual

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
REGULATOR
Gooseneck Single Spout Kitchen Faucet Installation Guidelines
Page 1 of 4
Rev - 01
10.9.2014
These guidelines have been prepared for the professional contractor to aid in the installation of:
REGULATOR GOOSENECK SINGLE SPOUT KITCHEN FAUCET WITH METAL WHEEL HANDLE AND SPRAY
(STYLE No. RGKM20, RG20KM UK)
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
STYLE No. RGKM20†
SPECIFICATIONS:
Deck Thickness Maximum: 2” (51mm)
Fittings Hole Ø [Temperature Valve]: Ø2-1/4” (57mm)
Fittings Hole Ø [Spout]: Ø1-3/4” (44mm)
Handle Turn Angle: Quarter Turn
Inlet Connection Size: 3/8”
Inlet Connection Type: Compression Connection Hoses†
Integrated Diverter: Yes
Restricted Maximum Flow Rate: 2.2gpm (8.3liters/min) ‡
Spout Reach: 10” (254mm)
Spout Swivel: Yes
Spray Hose Length: 79”
Water Pressure Minimum: 20 psi (1.4 Bar)
Water Pressure Maximum: 80 psi (5.5 Bar)
Water Pressure Recommended: 45 psi (3 Bar)
† UK Style No.
RG20KM is supplied with 2 BSP adapters,
assembly required.
‡ Both spout and spray are flow regulated at 2.2gpm.
IMPORTANT:

To ensure this product is installed properly, you must
read and follow these guidelines.
 The owner/user of this product must keep this
information for future reference.
 This product must be installed by a professional
licensed contractor. Be sure your installation conforms
to all federal, state, and local codes. In the State of
Massachusetts, all installations must comply with the
rules and regulations set forth within 248 CMR.
 Inspect the product to ensure you have all the parts
required for proper installation.
 Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
 DO NOT use putty. Putty contains oil and can cause
permanent discoloration on certain materials such as
marble, granite and any porous surface.

Refer to the specification and assembly drawings
attached. Product is sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.

This product requires 2 holes on the mounting surface.
The Temperature Valve requires a Ø2-1/4” [57mm]
hole. The Spout requires a Ø1-3/4” [44mm] hole. The
Spout can be installed on either the left or right side
of the Temperature Valve. The TUBE can be cut to
accommodate different on-center spreads. The max
on-center spread is 12” [305mm].
FIGURE – 01
TEMPERATURE VALVE INSTALLATION:

The TEMPERATURE VALVE only mixes hot and cold
water. It does not have a volume/on/off function.
1. Remove the TEE and CHECK VALVE HOUSINGS from
the HOSES on the TEMPERATURE VALVE BODY. See
FIGURE – 02.
2. Remove the NUT, METAL WASHER, and RUBBER
WASHER from the SHANK on the TEMPERATURE
VALVE BODY. Do
NOT remove the O-RING beneath
the ESCUTCHEON. See FIGURE - 02.
3. Ensure that the HOSES are securely tightened to the
TEMPERATURE VALVE BODY, then insert the SHANK
through the Ø2-1/4” [57mm] hole on the mounting
surface making sure the O-RING is beneath the
ESCUTCHEON.
NOTE: The HOSES are marked with colored ZIP TIES
to identify their function,
Red for incoming hot supply
water, blue for incoming cold supply water and green
for outgoing mixed water. See FIGURE – 02.
12"
[305mm]
ADJUSTABLE
VALVE
Ø2-1/4"
[57mm]
SPOUT
Ø1-3/4"
[44mm]
SPOUT CAN BE
INSTALLED ON
EITHER THE
LEFT OR RIGHT
SIDE OF THE
VALVE