Waterworks R.W. Atlas Low Profile Three Hole Wall Mounted Lavatory Faucet with Metal Lever Handles - Manual

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
RW ATLAS
Wall Mounted Lavatory Faucet
INSTALLATION GUIDELINES
Page 1 of 3 8.9.2012
These guidelines have been prepared for the professional contractor to aid in the installation of:
RW ATLAS WALL MOUNTED LAVATORY WITH METAL WHEEL HANDLES (STYLE# RWLS60) &
METAL LEVER HANDLES (STYLE # RWLS70)
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
SEE SERVICE PART DOCUMENT FOR PART ORDERING, AVAILABLE ON WATERWORKS.COM
Metal Wheel Handles
Style No. RWLS60
Metal Lever Handles
Style No. RWLS70
SPECIFICATIONS:
Control Valve Rough-In Depth Maximum: 5 -1/4"
Control Valve Rough-In Depth Minimum: 3-1/4"
Drain Depth Maximum: 2-5/8"
Drain Depth Minimum: 3/8"
Drain Hole Diameter: 1-3/4"
Drain Style: Push Touch (Drain Included)
Fitting Hole Diameter: 1-3/8"
Handle Spread: 8" (NOT ADJUSTABLE)
Inlet Connection Size: 1/2"
Inlet Connection Type: Female NPT
Maximum Water Pressure: 80psi
Minimum Water Pressure: 20psi
Recommended Water Pressure: 45psi
Restricted Maximum Flow Rate: 2.2gpm
REQUIRED PLUMBING DETAILS:
Universal Lavatory Wall Mounted Rough (For RWVC60)
STYLE No. GULV27
CODE No. GUSV27
Universal Lavatory Wall Mounted Rough (For RWVC70)
STYLE No. GULV25
CODE No. GUSV25
IMPORTANT:
¾ To ensure this product is installed properly, you
must read and follow these guidelines.
¾ The owner/user of this product must keep this
information for future reference.
¾ The faucet must be onsite prior to rough-in and
allows the installer to visualize the installation and
match the 8" center spread.
¾ Be sure your installation conforms to federal state,
and local codes. In the State of Massachusetts, all
installations must comply with the rules and
regulations set forth within 248 CMR.
¾ This product must be installed by a professional
licensed contractor.
¾ Inspect this product to ensure you have all the parts
required for proper installation.
¾ Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
¾ DO NOT use putty on fittings.
ROUGH-IN:
¾ Rough-in Depth from center of inlets to surface of
finished wall is 3-1/4" Minimum and 5-1/4" Maximum.
¾ Rough-in Height: 3-3/4" minimum from center of
cartridge stem to surface of countertop to allow for
lever handle clearance in the open position.
¾ See Figure - 01 for steps 1-6
1. Run 1/2" hot and cold supply lines. The spread
between supplies is 8" on center and is NOT
adjustable.
2. Pre-solder a 1/2" male NPT x 1/2" Sweat adapter
(not supplied) to a small piece of 1/2" copper pipe
prior to threading into the valve body.
3. Thread the adapters into the valve and attach to the
supplies using 1/2" couplings (not supplied).
4. Verify the supplies are secure, level, and at the
proper spread of 8" and at equal depths prior to
making final solder connections.
5. Install a 1/2" NPT nipple (not supplied) to
temporarily serve as a spout.
6. Verify the supplies and valve body are secure, then
turn on the supplies and check for leaks.