Waterworks Julia Three Hole High Profile Kitchen Faucet, Metal Cross Handles User Manual
Installation guidelines
Julia
®
Kitchen Mixer
6/05
W A T E R W O R K S
®
These guidelines have been prepared for the professional contractor to aid in the installation of:
JULIA KITCHEN MIXER (JUKM17)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
thread the base escutcheon (10) onto the side valve
until it contacts the mounting surface.
6. Thread the cover (11) onto the cartridge hand tight at
which point it will stop.
7. Unthread the base escutcheon until it contacts the cover
which will assure proper side valve height.
8. Tighten the nut (14) up against the underside of the
mounting surface to secure the side valve.
9. Reinstall the handle and index assembly.
10. Repeat these steps to install the second side valve.
SPOUT INSTALLATION:
11. Remove the tee assembly (30-32) and spout
attachment hardware (29a[x1] - 29c) from the spout
shank (29).
12. Insert the spout assembly (19-29a[x1], 33, 34) through
the spout hole of the mounting surface.
13. Place 1 rubber spout gasket (29a) then spout washer
(29b) and nut (29c) onto the spout shank.
14. Tighten the nut to secure the spout to the mounting
surface.
15. Reinstall the tee assembly then connect each of the
supply hoses to the adjacent side valve making sure they
are not pinched/kinked.
16. Connect the side valves (15) to the water supply valves
(not supplied).
INSPECT THE INSTALLATION:
17. Unscrew and remove the aerator assembly (33-34)
which includes a flow restrictor.
18. Carefully open the hot and cold valves to flush out any
debris in the supply lines.
19. Inspect all connections for leaks.
20. Close the valves and reinstall the aerator assembly.
➢ If further assistance is required, please contact Product
Support at 1-800-927-2120 (8am-7pm EST)
8 - 12"
3
1
/
4
"
Ø2
7
/
16
"
1
5
/
8
"
max.
10"
9
5
/
8
"
5
1
/
2
"
Ø2
3
/
4
"
JUKM17
IMPORTANT:
➢
➢ T
To
o e
en
nssu
urre
e tth
hiiss p
prro
od
du
ucctt iiss iin
nssttaalllle
ed
d p
prro
op
pe
errllyy,, yyo
ou
u m
mu
usstt
rre
eaad
d aan
nd
d ffo
ollllo
ow
w tth
he
esse
e ggu
uiid
de
elliin
ne
ess..
➢
➢ T
Th
he
e o
ow
wn
ne
err//u
usse
err o
off tth
he
e ffaau
ucce
ett m
mu
usstt kke
ee
ep
p tth
hiiss iin
nffo
orrm
maattiio
on
n
ffo
orr ffu
uttu
urre
e rre
effe
erre
en
ncce
e..
➢ Be sure your installation conforms to local codes.
➢ Refer to the specification and assembly drawings
attached. Faucet is sold partially assembled but shown
fully disassembled for illustrative and service purposes
only.
➢ Inspect this product to assure you have all parts required
for proper installation.
➢ Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
➢ If possible, install the faucet assembly on the sink or
mounting surface before setting.
➢ Do NOT use putty during this installation.
SIDE VALVE INSTALLATION:
1. Disassemble the index assembly (1-5) as 1 unit from the
handle hub (8) by lifting the ring (1) off of the handle.
2. Insert a bladed screw driver into the handle and loosen
the screw (6) then pull the handle off the cartridge (11).
3. Unthread the cover (9) from the cartridge then base
escutcheon (10) from the side valve (15). Remove 1
sealing gasket (12) as an upper seal. Do NOT remove
the other sealing gasket or hardware (12-14).
4. Insert the side valve into the hole in the mounting
surface so at least 1" of threads are exposed.
5. Install the upper sealing gasket onto the side valve then