Waterworks Julia Wall Mounted Two Hole Bridge Articulated Kitchen Faucet, Metal Cross Handles - Manual

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
JULIA
Wall Mounted Two Hole Bridge Articulated Kitchen Faucet Installation Guidelines
Page 1 of 2
Rev - 01
10.30.2014
These guidelines have been prepared for the professional contractor to aid in the installation of:
JULIA WALL MOUNTED TWO HOLE BRIDGE ARTICULATED KITCHEN FAUCET WITH METAL CROSS HANDLES
(STYLE No. JUKM05, JU05KM UK).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
STYLE No. JUKM05†
SPECIFICATIONS:
Fittings Hole Diameter: Ø1-3/8" (35mm)
Handle Spread (
NOT adjustable): 5-7/8” (150mm)
Handle Turn Angle: Quarter Turn
Inlet Connection Size & Type: 1/2" Male NPT†
Inlet Supply Spread Minimum: 5-1/2” (140mm)
Inlet Supply Spread Maximum: 6-5/16” (160mm)
Restricted Maximum Flow Rate: 2.2gpm (8.3liters/min)
Spout Reach: 20-7/8” (530mm)
Spout Swivel: Yes
Water Pressure Minimum: 20 psi (1.4 Bar)
Water Pressure Maximum: 80 psi (5.5 Bar)
Water Pressure Recommended: 45 psi (3 Bar)
† UK Style No.
JU05KM is supplied with a BSP adapter,
assembly required.
IMPORTANT:

To ensure this product is installed properly, you must
read and follow these guidelines.
 The owner/user of this product must keep this
information for future reference.
 This product must be installed by a professional
licensed contractor.
 Be sure your installation conforms to all federal, state,
and local codes. In the State of Massachusetts, all
installations must comply with the rules and
regulations set forth within 248 CMR.
 This product must be on-site prior to rough-in. This
allows the installer to visualize the installation and
verify dimensions.

Inspect the product to ensure you have all the parts
required for proper installation. Use only a strap
wrench or protected/smooth-jaw wrench on any
finished surface.
 DO NOT use putty. Putty contains oil and can cause
permanent discoloration on certain materials such as
marble, granite and any porous surface.
 Refer to the specification and assembly drawings
attached. Product is sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.
 Check incoming water pressure.
ROUGH-IN:
1. Determine the ideal location based on the clients
preference and install adequate blocking to properly
support the inlet supplies.
2. Finish the rough-in by installing well supported hot
and cold 1/2" female NPT connections. Be sure that
the supplies are level, secure and within the on-center
spread range. The on-center spread of the inlet
supplies must be between 5-1/2” (140mm) and 6-5/16”
(160mm). See FIGURE – 01.
FIGURE - 01
INSTALLATION:

The supplied NIPPLES have offset inlet and outlet
connections. See FIGURE – 02. The offset allows for
the inlet supply spread range shown above.
FIGURE - 02
3. Install the NIPPLES onto the inlet supplies. The
NIPPLES must project 1” (25mm) to 1-1/2" (38mm)
from the finished wall. Be sure that the NIPPLES are
level, securely tightened, and have an on-center
spread of 5-7/8” (150mm). See FIGURE – 03.
HOT INLET
SUPPLY
COLD INLET
SUPPLY
HOT INLET
SUPPLY
COLD INLET
SUPPLY
INLET SUPPLY SPREAD
5-1/2" (140mm) MIN
6-5/16" (160mm) MAX
1/2" Male NPT
Connection
1/2" Male NPT
Connection
C/L
C/L