Rally Armor 08-11 Subaru Impreza & 08-10 WRX - Manual

Rally Armor 20
Please read the
installing your
Your mud flap set
Your mounting ha
4 Round Edge Clip
6 Polygon Edge Cl
10 Washers ………
6 Short Stainless S
4 Long Stainless S
2 Rear Spacers……
2 Rear Clamps (fo
2 Front Brackets (
Recommended
For the rear wh
• Op
• Op
sec
Front Mud Flap
Summary‐ In th
• Re
• Se
• Pla
• Re
• Ali
Start: Begin
below). For ve
or prying (B2) t
of the side skirt
separating the
required (enou
TIP #1: Be car
TIP #2: To Rem
008+ Subaru Impreza
e instructions thorou
mud flaps. Rally Arm
t contains 4 flaps total *
ardware has been check
ps for the front………………
lips for the rear……………
……………………………………
Steel Screws (used for R
Steel Screws (used for Fr
………………………………………
or drill‐less installation) …
( UR sets only ) ...……………
d tools: Phillips screw
heel area there are tw
ption #1 (Drill‐less): Rubb
ption #2 (Extra secure Re
cure installation method
p Installation
his section you will:
emove the stock clips
eparate the liner from
ace clips over the mo
eplace liner/skirt piec
ign and bolt mud flap
by turning the steer
hicles equipped with
the inner piece out fir
t will temporarily nee
skirt (figure “C” belo
gh to gain access to
eful not to tear the whe
move the various clips o
a 2.5i/WRX –Mud fla
ughly before attemp
mor always recomm
2 front (2 mounting poin
ked at our facilities. It co
………. (Item
………… (Item
………... (Item
Rear).. (Item
ront).. (Item
……….. (Item
………. (Item
……… (Item
wdriver (short and/or
wo options available
ber mallet or hammer fo
ear drill installation reco
d.
s that attach the fend
m the body of the veh
ounting holes.
ces
p on the vehicle usin
ing wheel all the way
h a side skirt piece (F
rst , then prying the w
ed to be detached sl
ow) from the body, th
the wheel well area
eel well plastic, especiall
n the vehicle:
For the inserts with a s
unscrew the inner scre
clip, and pry the edges
order to remove the cl
ap Mounting Instruct
pting to mount your
ends professional in
nts) and *2 rear (3 moun
onsists of:
RoCl)
PolCl)
FenWash)
1SS)
1.5SS)
m 1‐2SP)
RRCLMPWRX)
BRWRX08)
r offset Phillips) ‐ Flat
e:
or clamp, (optional‐ can
ommended for competit
der liner (front of sid
hicle.
g hardware.
y towards the side yo
igure (B), remove the
whole assembly out o
ightly from the vehic
hey will detach indiv
and pull back the fen
y the upper regions whe
screw type head simply
ew enough to unlock the
s of the out ring portion in
lip completely:
tions.
mud flaps. Rally arm
nstallation.
nting points).
t head screwdriver.
of rubberized undercoa
tive driving, light off‐roa
de skirt) to the vehicl
ou are working on an
e first two plugs und
of the side skirt area.
cle. Starting from the
idually as you work y
nder liner (figure “D”
ere it meets the fender.
For the side skirt rivet ty
skirt pushing the inner p
will
unlock the assembly
mor recommends fol
ating or equivalent) ‐ if u
d or lowered vehicles):
e.
nd remove the stock
derneath the side ski
To gain access to th
e front end of the veh
your way towards th
” below) is needed.
It tears easily if mishan
pe assembly usually found o
ortion
in with a small pick or
and allow it to be removed:
llowing proper safet
using clamp installation m
Drill (Philips driver) 1/8 t
fender liner clips fro
rt. The clips can be r
e area behind the fe
hicle, slowly pry the
e rear of the vehicle
ndled.
on the side
r screwdriver,
ty precautions when
method for the rear.
th “or smaller drill bit if us
om the vehicle (Figur
emoved by unscrewi
ender liner, the front
side clips out by gen
. Only the first few c
1
n
sing full
re “A”
ing (B1)
portion
ntly
lips are