beautypg.com

Dell PowerVault 745N User Manual

Page 31

background image

Memory allocation error

 

Memory bank population

error!

 

Memory modules are not

installed in identical pairs;
faulty memory module(s).

 

Ensure that the memory modules are properly installed. See "

Memory Module Installation

Guidelines

" in "Installing System Components." If the problem persists, see

"

Troubleshooting System Memory

" in "Troubleshooting Your System."

 

Memory parity interrupt at

address

 

Faulty or improperly installed

memory modules.

 

Ensure that all memory modules are properly installed. See "

Memory Module Installation

Guidelines

" in "Installing System Components." If the problem persists, see

"

Troubleshooting System Memory

" in "Troubleshooting Your System."

 

Memory tests terminated by

keystroke

 

The spacebar was pressed

during POST to terminate the
memory test.

 

Information only.

 

No boot device available

 

Faulty or missing hard drive or

hard-drive subsystem.

 

 

Check the Integrated Devices configuration settings in the System Setup program. See

"Using the System Setup Program" in your User's Guide. Ensure that either SCSI Controller
or Integrated Drive Controller is enabled. If the system is booting from a SCSI controller,
ensure that the controller is properly connected. If the problem persists, replace the faulty
hard drive. See "

Installing a Hard Drive

" in "Installing Drives."

 

No boot sector on hard-

disk drive

 

An operating system is not on

the hard drive.

 

Check the hard drive configuration settings in the System Setup program. See "Using the

System Setup Program" in your User's Guide.

 

No timer tick interrupt

 

Faulty system board.

 

See "

Getting Help

."

 

Non-system disk or disk

error

 

Faulty hard drive or hard-drive

subsystem; no operating
system on hard drive.

 

See "

Troubleshooting Hard Drives

" in "Troubleshooting Your System."

 

PCI BIOS failed to install

 

Loose cables to expansion

card(s); faulty or improperly
installed expansion card.

 

Ensure that all appropriate cables are securely connected to the expansion cards. See

"

Troubleshooting Expansion Cards

" in "Troubleshooting Your System."

 

Plug & Play Configuration

Error

 

Error encountered in initializing

PCI device; faulty system
board.

 

Install the NVRAM_CLR jumper and reboot the system. See

Figure A

-2

for jumper location.

Check for a BIOS update. If the problem persists, see "

Troubleshooting Expansion Cards

" in

"Troubleshooting Your System." If the problem persists, see "

Troubleshooting the System

Board

."

 

Read fault

 

Requested sector not found

 

Faulty hard drive.

 

Ensure that the hard drive cables are properly connected. See "

Troubleshooting Hard

Drives

" in "Troubleshooting Your System" for the appropriate drive(s) installed in your

system.

 

Reset failed

 

Improperly connected drive

interface or power cable.

 

Ensure that the interface and power cables are securely connected. See "

Troubleshooting

Hard Drives

" in "Troubleshooting Your System."

 

ROM bad checksum = address

 

Faulty or improperly installed

expansion card.

 

Remove and reseat the expansion cards. See "

Troubleshooting Expansion Cards

" in

"Troubleshooting Your System."

 

Sector not found

 

Seek error

 

Seek operation failed

 

Faulty hard drive.

 

Replace the hard drive. See "

Troubleshooting Hard Drives

" in "Troubleshooting Your

System" for the appropriate drive installed in your system.

 

Shutdown failure

 

Shutdown test failure.

 

Ensure that all memory modules are properly installed. See "

Troubleshooting System

Memory

" in "Troubleshooting Your System." If the problem persists, see "

Troubleshooting

the System Board

."

 

Time-of-day clock stopped

 

Faulty battery; faulty system

board.

 

See "

Troubleshooting the System Battery

" in "Troubleshooting Your System." If the

problem persists, see "

Troubleshooting the System Board

."

 

Time-of-day not set -

please run SETUP program

 

Incorrect Time or Date

settings; faulty system battery.

 

Check the Time and Date settings See "Using the System Setup Program" in your User's

Guide. If the problem persists, see "

Troubleshooting the System Battery

" in

"Troubleshooting Your System."

 

Timer chip counter 2

failed

 

Faulty system board.

 

See "

Getting Help

."

 

 

Faulty or improperly installed

memory modules or faulty

 

Ensure that all memory modules are properly installed. See "

Memory Module Installation

Guidelines

" in "Installing System Components." If the problem persists, see