Great Plains NTA2007HD Operator Manual User Manual
Operator manual, Manufacturing, inc, 6m/20ft no-till heavy duty air drill
This manual is related to the following products:
Table of contents
Document Outline
- Operator Manual
- Table of Contents
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Wear Protective Equipment
- Use A Safety Chain
- Avoid High Pressure Fluids
- Minimize Radiation Exposure
- Handle Chemicals Properly
- Confined Space
- Tire Safety
- Use Safety Lights and Devices
- Keep Riders Off Machinery
- Transport Machinery Safely
- Shutdown and Storage
- Practice Safe Maintenance
- Safety At All Times
- Safety Decals
- Safety Reflectors and Decals
- Reflector: Slow Moving Vehicle (SMV)
- Reflectors: Red Triangles
- Reflectors: Fluorescent Panels
- Reflectors: Red
- Reflectors: Daytime
- Reflectors: Amber
- Transport: Speed
- Transport: Brake Roll-Away (Option)
- Danger: Read Manual
- Danger: Do Not Ride
- Danger: Crush (Marker Option)
- Danger: Electrocution
- Danger: Hitch Crushing
- Danger: Marker Crush (Option)
- Danger: Chemicals
- Danger: Chemicals (Option)
- Danger: Wing Crushing
- Danger: Marker Pinch (Option)
- Warning: Fan Hazard
- Warning: Moving Chain
- Warning: Wear Eye Protection
- Warning: Pinch Point
- Warning: High Pressure Fluid
- Warning: Confined Space
- Warning: Moving Gears
- Warning: Pinch Point
- Warning: Falling Hazard
- Warning: Hand Pinch
- Caution: Read Operator Manual
- Caution: Radar in Use
- Caution: Tire Pressure and Torque
- Caution: Tire Pressure and Torque
- Caution: Tire Pressure and Torque
- Caution: Tires Not A Step
- Caution: Use Adequate Tractor
- Introduction
- Preparation and Setup
- Operating Instructions
- Pre-Start Checklist
- Unfolding and Folding
- Lowering and Raising Air Drill
- Transporting the Air Drill
- Brake Operation (option)
- Ladder Operations
- Hopper and Tank Lid Operations
- Meter Doors
- Loading Materials
- Calibration Crank, Bag and Scale
- Air System Operation
- Marker Operation (Option)
- Field Operations
- Field Operation
- Parking
- Storage
- Adjustments
- Adjustments Summary
- Setting Material Rates
- Check Contact Tire
- Check Flute Shaft Configuration
- Find Your Chart and Rate
- Monitor Material Configuration
- GRAN SEED MONITOR GRAN FERT MONITOR
- Material Configuration Setup Screen for Dry Fertilizer
- Channel Setup Screen
- GRAN SEED CONTROL GRAN FERT CONTROL
- Example Material Library:
- Update Material Library
- Create a Controlled Material
- Example Non-Preset Material Setup:
- Actuator Channel Setup
- Example Channel Setup:
- Calibrate
- Meter Rate Adjustment
- Meter Calibration
- Planting Depth Adjustments
- Adjusting Tool Bar Height
- Air System Adjustments
- Weight Transfer Adjustments
- Frame-Mounted Coulters
- 07HD Row Unit Adjustments
- Marker Adjustments
- Troubleshooting
- Maintenance and Lubrication
- Maintenance Lift Lock
- Hopper Strap Maintenance
- Chain Maintenance
- Maintenance
- Fertilizer System Maintenance
- Unloading Materials
- Material Clean-Outs
- Implement Lift Switch Adjustment
- Contact Drive Re-setting
- Hydraulic Maintenance
- Brake Maintenance (Option)
- Leveling Implement
- Marker Maintenance (Option)
- Seed Flap Replacement
- Lubrication and Scheduled Maintenance
- Hopper Straps
- Wing Flex Pivots
- Marker Tilt Bearings (Option)
- Cart-Implement Link
- Rear Lower Parallel Arms
- Rear Upper Parallel Arms
- Coulter Pivots
- Fertilizer Pump Bearings (Option)
- Fertilizer Pump Crankshaft (Option)
- Tire Pressures
- Contact Drive Chains
- Drive Chains (Single-Hopper)
- Drive Chains (Dual Hopper)
- Drive Chains (w/Liquid Fertilizer, Option)
- Hopper Lid Pivot Bar and Clamps
- Meter Box Door Clamps
- Caster Pivots
- Caster Brakes
- Cart Wheel Bearings
- Gauge Wheel Bearings
- Coulter Hub Bearings
- Hopper Lid Seals
- Meter Door Seals
- Options
- Appendix A - Reference Information
- Appendix B - Initial Setup
- Appendix C - Option Installation
- Index