SDC 921P EntryCheck - Manual (Page 5)

FACTORY DEFAULTS
Master Programming CodeWWW..WWWWWWW.W.W...123456
Entry Code LengthWWWWWWWWWWWWWWW.WW..4 digits
Entry ModeWW..WWWWWWWWWWWWWW.W...Card or PIN
Request-to-exit Output RelayWWWWWWWWW...........No Output
Alarm Shunt OutputW.WWWWWWWWWWWWW.........Disabled
Forced Entry OutputWWWWWWWWWWW..WWWW..No Output
Door Ajar OutputWWWWWWWWWWWWW..WW.W...No Output
Main Relay On TimeWWWWWWWWWWWWW..W..02 Seconds
Auxiliary Relay On TimeWWWWWWWWWWW.....W02 Seconds
Solid State Output #3 On TimeWWWWWWWWW......02 Seconds
Solid State Output #4 On TimeWWWWWWWWWW..02 Seconds
Door Sense/Inhibit InputWWWWWWWWWW...WW..Door Sense
Keypad Lockout OutputWWWWWWWWWWWW..WW.Disabled
Keypad Active OutputWWWWWWWWWWWW..W..W..Disabled
Beeper Sounds When Key PressedWWWWWWWW...WWWYes
Beeper Sounds During Relay #1WWWWWWWWW..W...WW.No
Beeper Sounds During Relay #2WWWWWWWWWWW...W...No
Beeper Sounds During Output #3WWWWWWWWWWW .....No
Beeper Sounds During Output #4WWWWWWWWWWW........No
Keypad Lockout CountWWW.WWW......W.3 Tries Before Lockout
Anti-Passback TimeWWWWWW..WW...WWW.No Anti-Passback
Auto-RelockWWWWWWWWWWWWW...WWWW.WWWW.On
Entering Programming Mode
The 6-digit Master Programming Code (default = 123456) is used
to enter Programming Mode.
Press: # 9 # Master Code #
Master Code = the current 6-digit Master Programming Code
Setting Entry Code Length Default: 4 digits
Press: 03 # Length #
Length = 4-6 for entry code length
Note: If the Entry Code Length is going to be changed from the factory
default of 4 digits, make this change first before programming any entry
codes.
Adding a New User
User PIN Only Access (No Card)
Press: 01 # User # Code # Code # Relay #
---- Or ----
User Card and/or PIN Access
Press: 06 # User # Code # Code # Relay # Present Card
User=User number to be added: 001-500
Code=The new entry code: 1-999999, depending on code length
Relay=Relay output entry code will activate:
1=Main Relay 2=Auxiliary Relay 3=Both Relays
10=Relay #1, toggled 20=Relay #2, toggled 30=both Relays toggled
12=Relay #1 toggled; Relay #2 timed open
21=Relay #1 timed open; Relay #2 toggled
The yellow indicator will flash quickly while the 921P stores the new
user information in memory The green indicator will light when the
new code and card are accepted. If the user number already exists
or an entry error has been made, the red indicator will light. Delete
the user and re-enter the new information again.
Note: Leading zeros (zeros before the code number, i.e.0001) do not need to
be entered when programming a new code. The 921P will internally add any
zeros to fill digits determined by the entry code length setting. Leading zeros
will have to be entered by the user when entering their code to gain access.
Erasing a Single User
Press: 02 # User # User #
User =The user number to delete (001-500)
The yellow indicator will flash quickly while the 921P erases the
user from memory. The green indicator will light when the code is
erased.
Output Toggle Mode
When an output is programmed for Toggle Mode, the output
alternates from OFF to ON or from ON to OFF each time it is
accessed. When an output is toggled on, the green LED remains
solid until toggled off.
The rules for a toggle output are:
If the output is OFF, it will turn ON and stay on until the next
activation.
If the output is ON, it will turn OFF and stay off until the next
activation.
An authorized PIN, Card, or REX input programmed to
momentarily activate that same relay will reset the relay to its
normal state.
Exiting Programming Mode
Press: #
The red indicator will light after exiting Programming Mode
Note: The 921P will automatically exit Programming Mode after
two minutes of inactivity
**
Re-entering a Command After a Mistake
If the red indicator lights, signaling an incorrect entry, or an
incorrect key is pressed during programming, to clear the keypad
and re-enter the command:
Press: 9 # *
Erasing Multiple Users (Sequential)
Press: 09 # 1 st User # Number of users #
1 st User =Starting user number to delete
Number of users = Total number of consecutive users to delete
The yellow indicator will flash quickly while the 921P erases the
user from memory. The green indicator will light when the code is
erased.
Adding Multiple Sequential Cards
Press: 07 # 1 st User # Code # Code # Relay # Number of users
# Present 1 st card
1 st User =Starting user number to add
Number of users = Total number of consecutive cards to add
The yellow indicator will flash quickly while the 921P erases the
user from memory. The green indicator will light when the codes
have been added.
Select Entry Mode Default: Card or PIN
Sets the entry mode for the 921P.
Press: 05 # Mode #
Mode=Operating Mode(1-3)
1=Card or PIN; 2=Card Only 3=Card and PIN
P:\INSTALLATION INST\Access Controls\INST-921\INST-921P.vsd Rev C 04-14 Page 5
BASIC PROGRAMMING
When the 921P EntryCheck™ is in Programming Mode the yellow
indicator will blink slowly. After a programming command is
selected, the yellow indicator will flash rapidly while the keypad is
waiting for user input data. The green indicator will light if the data
is accepted. The red indicator will light if any programming data is
entered incorrectly, and the command will have to be fully re-
entered.