Installation instruc tio ns – Poison Spyder TRAIL CORNERS User Manual

Page 2

INSTALLATION INSTRUC

TIO

Poison Spyder Customs • TRAIL CORNERS INSTALLATION

Page 2

flare. This gap is OK at this point, it will be

addressed later when the Trail Corners are

bolted into place.
5. Use a fine-tip felt pen to mark the mounting

hole locations (mark through the mounting

holes in the Trail Corner, onto the Jeep’s

sheet metal). If you purchased Trail Corners

for LED taillights, mark the large taillight hole

as well.

6. Remove the Trail Corner from the vehicle.

Check behind the Jeep’s sheet metal at

each marked location for wires and other

obstructions. Remove, re-locate or hold

them out of the way during drilling during the

following step.

7. Use a center punch and hammer to lightly

mark the center of each of your mounting

hole marks. Drill the mounting holes using a

1/4” drill bit. Use a file to de-burr the edges

of the holes.

8. If you are installing LED taillights, use a

4-1/2” hole saw to cut out the marked hole

for the taillight. Use a file to de-burr the edge

of the cut.

9. Spray the exposed bare metal around the

edges of the holes with aerosol clear coat or

other paint of your choice to prevent rust.

10. Place the Trail Corner back onto the vehicle

and fasten it into place using the provided

hardware. Be sure to place the flat washers

on the inside of the Jeep tub, under the lock

nuts (NOT under the button heads).

11. If there is a gap between the Trail Corner

and the fender flare, loosen the fasteners for

the flare and manipulate it into place, snugly

against the edge of the Trail Corner (this may

require slightly enlarging the mounting holes

in the flare).

12. Re-install taillight (unless using LED’s)

and gas filler bezel, as well as any other

components that were removed at the

beginning of this procedure.

13. Repeat the previous procedures to install

the opposite side Trail Corner.

14. If installing LED taillights, continue

with Poison Spyder’s separate instruction

sheet “LED TAILLIGHTS & FLASHERS

INSTALLATION.”

WARRANTY

Poison Spyder Customs™ warranties all of

the products we sell and distribute for one (1)

year from the date of sale. These products will be

free from defects in material and workmanship

under normal installation, and use. Due to the

intended use the powder coat finish is warranted

for ninety (90) days. The finish warranty will not

cover a product if it has been damaged in any

way. Warranty is limited to repair or replacement.

Poison Spyder Customs™ does not offer any

type of labor or shipping allowance and all

warranty claims are subject to inspection by

Poison Spyder Customs™.
At the discretion of Poison Spyder Customs™,

the products in question can be repaired or

replaced when found defective. Prior to any

replacement or repair, written authorization must

be obtained from Poison Spyder Customs™.

Failure to contact us prior to having warranty work

preformed will immediately void all applicable

warranties; and it is then the sole responsibility

of the customer to remit any payment incurred.
The warranty expressed above is the sole

warranty of Poison Spyder Customs™, and

any other expressed or implied warranties are

hereby specifically excluded and disclaimed.

HOLD HARMLESS AGREEMENT
1. In purchasing a Poison Spyder Customs

Product™ I release, waive, discharge and

covenant not to sue Poison Spyder Customs

officers, servants, agents, or employees

(hereinafter referred to as Releasees) from

any and all liability, claims, demands, actions

and causes of action whatsoever arising out

of or related to any loss, damage, or injury,

including death, that may be sustained by

me (or anyone else), any property belonging

to me (or anyone else), whether caused by

the negligence of the releasees or otherwise,

while working on, using or any activity related

to this product.

2. I am fully aware of risks and hazards connected

with the use of a this product and I elect to

voluntarily engage in such use of this product

knowing that the use may be hazardous to

me and my property. I voluntarily assume full

responsibility for any risks of loss, property

damage or personal injury, including death,