Campbell Scientific CDM-VW300 Series Dynamic Vibrating-Wire Analyzer System User Manual
Cdm-vw300 series dynamic vibrating-wire analyzers
Table of contents
Document Outline
- Revision and Copyright Information
- Warranty
- Assistance
- Table of Contents
- 1. Introduction
- 2. Cautionary Statements
- 3. Initial Inspection
- 4. Overview
- 5. Specifications
- 6. Installation
- 7. System Operation
- 7.1 PC Based Tools
- 7.2 Using the Datalogger
- 7.3 Using the SC-CPI Interface
- 7.4 Using Power Supplies
- 7.5 Configuring the CDM-VW300 Analyzer
- 7.5.1 Device Name
- 7.5.2 CPI Bus Speed
- 7.5.3 Operating System Version
- 7.5.4 Operating System Date
- 7.5.5 Analyzer Serial Number
- 7.5.6 Display Rate
- 7.5.7 Dynamic Sample Rate
- 7.5.8 Device Type
- 7.5.9 CPI Bus Address
- 7.5.10 System Options
- 7.5.11 Channels Enabled
- 7.5.12 Desired Resonant Amplitude
- 7.5.13 Minimum- and Maximum Cut-Off Frequencies
- 7.5.14 Frequency-Output Format
- 7.5.15 Multipliers and Offsets
- 7.5.16 Steinhart-Hart Coefficients
- 7.5.17 Rainflow-Histogram Output Configurations
- 7.6 Sensor Selection
- 7.7 System Connections
- 7.8 Operating System
- 7.9 Power-Up Sequence
- 7.10 CRBasic Programming
- 7.11 System Adjustments
- 7.12 System Validation
- 8. Troubleshooting
- 8.1 Connections
- 8.2 Power
- 8.3 Isolating Components
- 8.4 Filtering Harmonics
- 8.5 Diagnostic Outputs
- 8.6 Factory Default Reset
- 9. Glossary
- 10. References and Attributions
- Appendix A. Measurement Theory
- Appendix B. SC-CPI Datalogger to CPI Interface
- Appendix C. CDM Devices and CPI Bus
- Appendix D. Digits Conversion
- Appendix E. Calculating Measurement Error
- Appendix F. Thermistor Information
- Appendix G. CRBasic Program Library
- G.1 Dynamic Measurements
- G.1.1 20 Hz Measurement Example — One CDM-VW300, Two Channels
- G.1.2 20 Hz Measurement Example — One CDM-VW305, Eight Channels
- G.1.3 20 Hz Measurement Example — Three CDM-VW305s, 24 Channels
- G.1.4 20 Hz Measurement Example — Six CDM-VW305s, 48 Channels
- G.1.5 50 Hz Measurement Example — One CDM-VW300, Two Channels
- G.1.6 50 Hz Measurement Example — One CDM-VW305, Eight Channels
- G.1.7 50 Hz Measurement Example — Three CDM-VW305s, 24 Channels
- G.1.8 50 Hz Measurement Example — One CDM-VW300, Two Channels, Rainflow Histogram
- G.1.9 50 Hz Measurement Example — One CDM-VW305, Eight Channels, Rainflow Histogram
- G.1.10 50 Hz Diagnostic Example — One CDM-VW300, Two Geokon 4000 Sensors with FieldCal()
- G.1.11 50 Hz Measurement Example — One CDM-VW300, Two Geokon 4000 Sensors with FieldCal()
- G.1.12 50 Hz Measurement Example — One CDM-VW300, Two Geokon 4000 Sensors with FieldCal() and CardOut() to CF
- G.1.13 50 Hz Measurement Example — One CDM-VW300, Two Geokon 4000 Sensors with FieldCal() and TableFile() to CF
- G.1.14 100 Hz Measurement Example — One CDM-VW300, Two Channels
- G.1.15 100 Hz Measurement Example — One CDM-VW305, Eight Channels
- G.2 Static Measurements
- G.1 Dynamic Measurements
- Campbell Scientific Companies