NORD Drivesystems BU2200 - Manual (Page 28)

5 Parameter
28 BU 2200 GB-3813
Bit 0 = Digital input 1 Bit 1 = Digital input 2
Bit 2 = Digital input 3* Bit 3 = Digital input 4*
Bit 4 = Digital input 5** Bit 5 = Digital input 6**
Bit 6 = Digital input 7** Bit 7 = Digital input 8**
* Except for ... CU4- modules
** Only SK TU4-ECT, SK TU4-EIP, SK TU4-PNT and SK TU4-POL
Pos : 62 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/Bus übergreif end [ P150 ff. - P180 ff. ]/Par amet er P175 – Baugruppenz us tand [SK TU4-..., SK EBIOE] @ 3\mod_1369119434666_388.doc x @ 69704 @ @ 1
P175
Relay Status
(Switching status of relay)
SK EB…
SK TU4- …
8 bit
0 ... 3 Image of the switching status of the relay outputs of the module.
Bit 0 = Relay 1 Bit 1 = Relay 2
Pos : 63 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/Bus übergreif end [ P150 ff. - P180 ff. ]/Par amet er P176 – Pr oz eßdaten Bus In [SK xU x-...] @ 3\mod_1369120373047_388.doc x @ 69728 @ @ 1
P176 ... [-01]
…
... [-25]
Process Data Bus In
(Process data Bus In)
SK TU3- …
SK xU4- …
16 bit
-32768 ... 32767 Bus data received from Bus Master / controller
[-01] = Bus module outputs* [-02] = Control word FI 1
[-03] = Setpoint 1 for FI 1 [-04] = Setpoint 2 for FI 1
[-05] = Setpoint 3 for FI 1 [-06] = Setpoint 4 for FI 1
[-07] = Setpoint 5 for FI 1 [-08] = Control word FI 2*
[-09] = Setpoint 1 for FI 2* [-10] = Setpoint 2 for FI 2*
[-11] = Setpoint 3 for FI 2* [-12] = Setpoint 4 for FI 2*
[-13] = Setpoint 5 for FI 2* [-14] = Control word FI 3*
[-15] = Setpoint 1 for FI 3* [-16] = Setpoint 2 for FI 3*
[-17] = Setpoint 3 for FI 3* [-18] = Setpoint 4 for FI 3*
[-19] = Setpoint 5 for FI 3* [-20] = Control word FI 4*
[-21] = Setpoint 1 for FI 4* [-22] = Setpoint 2 for FI 4*
[-23] = Setpoint 3 for FI 4* [-24] = Setpoint 4 for FI 4*
[-25] = Setpoint 5 for FI 4*
* Except for SK TU3 versions
Pos : 64 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/PO WER LIN K/ Par amet er P176 – Pr oz eßdaten Bus In (Ergänz ung POWERLINK) [SK xU x- POL] @ 4\mod_1378889464526_388.doc x @ 94562 @ @ 1
Information Control data via UDP
Control data via UDP are only displayed if there is no POWERLINK master.
Pos : 65 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/Bus übergreif end [ P150 ff. - P180 ff. ]/Par amet er P177 – Pr oz eßdaten Bus Out [SK xU x- ...] @ 3\mod_1369125104371_388.doc x @ 69776 @ @ 1