NORD Drivesystems BU2200 - Manual (Page 25)

POWERLINK Bus module –
Supplementary manual options for NORD - Frequency Inverters
BU 2200 GB-3813 25
P152
Factory Setting
(Load factory settings)
SK TU3- …
SK xU4- …
8 bit
0 ... 1
{ 0 }
With the selection of the relevant value anc confirmation with the OK key, the selected parameter
range is set to the factory setting. Once the setting has been made, the value of the parameter
automatically returns to 0.
0 = No change: Does not change the parameterisation.
1 = Loading the factory settings: The complete parameterisation of the FI reverts to the
factory setting. All originally parameterised data are lost.
Pos : 48 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/Bus übergreif end [ P150 ff. - P180 ff. ]/Par amet er P153 – Min.Systembusz ykl us [SK xU 4-..., SK EBIOE] @ 3\mod_1368690526763_388.doc x @ 65260 @ @ 1
P153 ... [-01]
... [-02]
Min. System Bus Cycle
(Minimum cycle time of system bus)
SK EB…
SK xU4- …
16 bit
0 ... 250.00 ms
{ [-01] = 10 }
{ [-02] = 5 }
In order to reduce the bus load on the system bus, the transmission cycle time of the Service
Data Objects and Process Data Objects can be extended.
[-01] = SDO Inhibit Time [-02] = PDO Inhibit Time
Pos : 49 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/Bus übergreif end [ P150 ff. - P180 ff. ]/Par amet er P154 – Z ugriff TB- IO [SK xU 4-...] @ 3\mod_1368694374103_388.doc x @ 65666 @ @ 1
P154 ... [-01]
... [-02]
TB-IO Access
(Access to technology unit IOs)
SK xU4- … 8 bit
0 ... 5
{ [-01] = 0 }
{ [-02] = 0 }
Assignment of the writing and reading rights of the connected frequency inverter to the inputs and
outputs of the technology unit.
[-01] = Inputs [-02] = Outputs
0 = OFF, no effect 1 = Broadcast, all FIs read the inputs
2 = FI 1, reads and writes to the IOs 3 = FI 2, reads and writes to the IOs
4 = FI 3, reads and writes to the IOs 5 = FI 4, reads and writes to the IOs
Pos : 50 /Anl eitungen/ Elektroni k/ Bus s yst eme/5. Par ameter/ P16x Spezifisc he Paramet er - Bus @ 3\ mod_1369132201341_388. doc x @ 70019 @ 5 @ 1
Specific Bus Parameters (P16x)
Parameter
{Factory seting}
Setting value / Description / Note Device Type
Pos : 51 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/PO WER LIN K/ Par amet er P160 – N odeId/ IP Adres se4 [SK xU x- POL] @ 4\mod_1378820577402_388.doc x @ 94361 @ @ 1
P160
Node Id/IP Address 4
(Node Id/IP Address 4)
SK TU3-POL
SK xU4-POL
8 bit
0 ... 239 Setting of the participant address (Node ID)  4. Byte of the IP address.
The setting is only adopted after a restart of the module.
Information Priority of parameter over DIP switch
A value "0" means that the setting has been made with the module DIP switches.
Pos : 52 /Anl eitungen/ Elektroni k/ Par ameter/ P100-P199/ Buss pezi fisch/PO WER LIN K/ Par amet er P162 – Geräte Name [SK xU x- POL] @ 4\mod_1378821740808_388.doc x @ 94385 @ @ 1