KROHNE PTIFLEX 2200 FOUNDATION FIELDBUS - Manual (Page 47)

OPERATION
4
47
OPTIFLEX 2200 C
www.krohne.com 09/2013 - 4002573201 - AD FF OPTIFLEX 2200 R01 en
PROBE_END_THRESHOLD PROBE_END_THRESHOLD PROBE_END_THRESHOLD PROBE_END_THRESHOLD
Probe end threshold Probe end threshold Probe end threshold Probe end threshold
RW For measurement in TBF mode. If it is difficult to identify the
probe end signal (for example: too many parasite signals) you
can increase the threshold of the signal. A threshold of 1000 is
equivalent to the amplitude of the measurement pulse. A
threshold of 100 is equivalent to 10% of the amplitude of the
measurement pulse.
PROBE_LENGTH PROBE_LENGTH PROBE_LENGTH PROBE_LENGTH
Probe Length Probe Length Probe Length Probe Length
RW The distance from the flange face / thread stop of the device
down to the bottom end of the probe (including counterweight
for cable versions). If probe length has been modified, enter
the new value here.
Setting:
0…40000
SECONDARY_VALUE SECONDARY_VALUE SECONDARY_VALUE SECONDARY_VALUE
electronic temperature electronic temperature electronic temperature electronic temperature
The Electronic temperature.
STATUS
Status
R Digital transducers, unlike their analog versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-0
VALUE
Value
R A numerical quantity entered by a user or calculated by the
algorithm.
SECONDARY_VALUE_UNIT SECONDARY_VALUE_UNIT SECONDARY_VALUE_UNIT SECONDARY_VALUE_UNIT
electronic temperature unit electronic temperature unit electronic temperature unit electronic temperature unit
RW The engineering units to be used with SECONDARY_VALUE
(electronic temperature).
°C
Setting:
K; °C; °F; °R
SENSOR_CAL_DATE SENSOR_CAL_DATE SENSOR_CAL_DATE SENSOR_CAL_DATE
Sensor Calibration Date Sensor Calibration Date Sensor Calibration Date Sensor Calibration Date
R The date of the last sensor calibration. -
SENSOR_CAL_LOC SENSOR_CAL_LOC SENSOR_CAL_LOC SENSOR_CAL_LOC
Sensor Calibration Location Sensor Calibration Location Sensor Calibration Location Sensor Calibration Location
R The last physical location at which the sensor was calibrated.
(ex. Acme Labs)
-
SENSOR_CAL_METHOD SENSOR_CAL_METHOD SENSOR_CAL_METHOD SENSOR_CAL_METHOD
Sensor Calibration method Sensor Calibration method Sensor Calibration method Sensor Calibration method
R The method of last sensor calibration. It could be one of the
several standard calibration methods defined by ISO or some
other method.
factory trim
standard
calibration
SENSOR_RANGE SENSOR_RANGE SENSOR_RANGE SENSOR_RANGE
Sensor Range Sensor Range Sensor Range Sensor Range
The High and Low range limit values, the engineering units
code and the number of digits to the right of the decimal point
for the sensor.
EU_100
max value
R The engineering unit value which represents the upper end of
range of the associated block parameter.
EU_0
min value
R The engineering unit value which represents the lower end of
range of the associated block parameter.
UNITS_INDEX
Units Index
R Device Description units code index for the engineering unit
descriptor for the associated block value.
DECIMAL
Decimal
R The number of digits to the right of the decimal point which
should be used by an interface device in displaying the
specified parameter.
2
SENSOR_SN SENSOR_SN SENSOR_SN SENSOR_SN
Sensor Serial Number Sensor Serial Number Sensor Serial Number Sensor Serial Number
R The sensor serial number.
SENSOR_TYPE SENSOR_TYPE SENSOR_TYPE SENSOR_TYPE
Sensor Type Sensor Type Sensor Type Sensor Type
R The type of sensor. Level
SENSOR_CAL_WHO SENSOR_CAL_WHO SENSOR_CAL_WHO SENSOR_CAL_WHO
Sensor Calibration Who Sensor Calibration Who Sensor Calibration Who Sensor Calibration Who
R The name of the person responsible for the last sensor
calibration.
TANK_HEIGHT TANK_HEIGHT TANK_HEIGHT TANK_HEIGHT
Tank Height Tank Height Tank Height Tank Height
RW The distance from the tank connecting flange face/thread stop
down to the tank bottom.
Setting:
0…100000
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value