KROHNE PTIFLEX 2200 FOUNDATION FIELDBUS - Manual (Page 44)

4
OPERATION
44
OPTIFLEX 2200 C
www.krohne.com 09/2013 - 4002573201 - AD FF OPTIFLEX 2200 R01 en
COUNTERWEIGHT_HEIGHT COUNTERWEIGHT_HEIGHT COUNTERWEIGHT_HEIGHT COUNTERWEIGHT_HEIGHT
Counterweight height Counterweight height Counterweight height Counterweight height
RW For installations where a cable probe is used with a
counterweight attached to it this parameter specifies the
height of the counterweight.
Setting:
0...PROBE_LENGTH
EMPTY_AREA EMPTY_AREA EMPTY_AREA EMPTY_AREA
Empty Area Empty Area Empty Area Empty Area
RW Empty Area
Setting:
0...PROBE_LENGTH
EPSILON_R_GAS EPSILON_R_GAS EPSILON_R_GAS EPSILON_R_GAS
Dielectric constant of the Dielectric constant of the Dielectric constant of the Dielectric constant of the
gas gas gas gas
RW A major parameter for TDR level measurement devices. If the
gas above the filling medium is not air, set this value to the
dielectric constant of the gas.
Setting:
0.8...115
EPSILON_R_PRODUCT EPSILON_R_PRODUCT EPSILON_R_PRODUCT EPSILON_R_PRODUCT
Dielectric constant of the Dielectric constant of the Dielectric constant of the Dielectric constant of the
product product product product
RW For measurement in TBF mode: Specifies the dielectric
constant of the product. If possible, type in the exact value. If
you do not know the exact value, use param.
AUTO_EPSILON_R for automatic calculation of the exact
value. A new dielectric constant that is too low will mean that
level will read higher than its true value.
Setting:
1...115
FULL_AREA FULL_AREA FULL_AREA FULL_AREA RW Full Area
Setting:
0...PROBE_LENGTH
LEVEL_LOST LEVEL_LOST LEVEL_LOST LEVEL_LOST
Level Lost Alarm Level Lost Alarm Level Lost Alarm Level Lost Alarm
RW Level Lost Alarm
Setting:
Warning / Error
LEVEL_OF_POINT_1_15 LEVEL_OF_POINT_1_15 LEVEL_OF_POINT_1_15 LEVEL_OF_POINT_1_15
Level table Level table Level table Level table
RW Table entries 1-15 containing level values.
LEVEL_OF_POINT_16_30 LEVEL_OF_POINT_16_30 LEVEL_OF_POINT_16_30 LEVEL_OF_POINT_16_30
Level table Level table Level table Level table
RW Table entries 16-30 containing level values.
LIN_TYPE LIN_TYPE LIN_TYPE LIN_TYPE
Linerization Type Linerization Type Linerization Type Linerization Type
R The linerization type used to describe the behavior of the
sensor output.
linear with
input
Setting:
Linear with input
MEASURE_THRESHOLD MEASURE_THRESHOLD MEASURE_THRESHOLD MEASURE_THRESHOLD
Measurement threshold Measurement threshold Measurement threshold Measurement threshold
RW If it is difficult to identify the level signal (for example: too
many parasite signals) you can increase the threshold of the
signal. A threshold of 1000 is equivalent to the amplitude of
the measurement pulse. A threshold of 100 is equivalent to
10% of the amplitude of the measurement pulse.
MINIMUM_LAYER MINIMUM_LAYER MINIMUM_LAYER MINIMUM_LAYER
Interface Minimum Layer Interface Minimum Layer Interface Minimum Layer Interface Minimum Layer
RW Interface Minimum Layer
OFFSET OFFSET OFFSET OFFSET
Offset Offset Offset Offset
RW Offset
OVERFILL_ERROR OVERFILL_ERROR OVERFILL_ERROR OVERFILL_ERROR
Overfill Error Overfill Error Overfill Error Overfill Error
RW Overfill Error Alarm
Setting:
Warning / Error
POINTS_NUM POINTS_NUM POINTS_NUM POINTS_NUM
Number of table entries Number of table entries Number of table entries Number of table entries
RW Number of entries in the conversion table for mass/volume.
Setting:
0...30
PRIMARY_VALUE_TYPE1 PRIMARY_VALUE_TYPE1 PRIMARY_VALUE_TYPE1 PRIMARY_VALUE_TYPE1
Primary Value Type Primary Value Type Primary Value Type Primary Value Type
R The type of measurement represented by the primary value.
For Example: Mass Flow, Absolute Pressure, Differential
Temperature.
level
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value