KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.38 to 2.47 - Manual (Page 37)

BOP HIPWR 080709
1-17
TABLE 1-5. ACCESSORIES
ITEM FUNCTION PART NUMBER
Mating Connector, Trigger Mates with Trigger port. 142-0527 (Kepco)
SP2501 (CUI Stack)
IEEE 1118 (BITBUS)
Mating connector Allows connection to IEEE 1118 (BITBUS) port. 142-0485 (Kepco)
KMDLA-5P (Kycon Inc.)
IEEE 488 Cable, (1 meter long) Connects BOP power supply to GPIB bus. SNC 488-1
IEEE 488 Cable, (2 meter long) Connects BOP power supply to GPIB bus. SNC 488-2
IEEE 488 Cable, (4 meter
longs) Connects BOP power supply to GPIB bus. SNC 488-4
Interconnection Kit for multiple
identical power supplies in par-
allel (increase output current) Cables required to connect multiple BOP models in parallel for
increased current capability, e.g., connecting two BOP 10-
75MG models in parallel to produce a virtual BOP 10-150MG. KIT 219-0449 (2 in parallel)
KIT 219-0446 (3 in parallel)
KIT 219-0447 (4 in parallel)
KIT 219-0448 (5 in parallel)
Interconnection Kit for multiple
identical power supplies in
series (increase output voltage) Cables required to connect multiple BOP models in series for
increased voltage capability, e.g., connecting two BOP 10-
75MG models in series to produce a virtual BOP 20-75MG. KIT 219-0443 (2 in series)
KIT 219-0444 (3 in series)
Interconnection Kit for multiple
identical power supplies con-
nected in two parallel branches
each comprised of 2 or 3 units
connected in series Cables required to connect two parallel branches of series con-
nected power supplies.
KIT 219-0480 is used for 2 parallel connected branches of 2
series connected units. The four (total) power supplies provide
double the output current and double the output voltage of a a
single unit
KIT 219-0481 is used for 2 parallel connected branches of 3
series-connected units. The six (total) power supplies provide
double the output current and triple the output voltage of a a
single unit KIT 219-0480 (2 in series X 2
parallel branches)
KIT 219-0481 (3 in series X 2
parallel branches)
Line Cord (250V, 20A) Provides connection to a-c mains via Nema 6-20P connector. 118-1087
Line Cord (250V, 20A) Provides connection to a-c mains via Nema L6-20P locking
type connector.
118-1088
RS 232 Cable Kit Contains RJ11 to RJ45 Patch cord, RJ 45 Patch cord, two RS
232 adapters, one with male pins to connect to DTE equipment
and one with female pins to connect to a PC (personal com-
puter), two RS 232 Loop Back test Connectors (one 6-pin and
one 8-pin) to test RS 232 communication and aid in isolating
RS 232 communication problems.
KIT 219-0436
RS 232 Adapter (Male pins) Allows RS 232 port to be connected to DTE equipment. (Sup-
plied in KIT 219-0436.) 142-0487
(L-COM RA098M)
RS 232 Adapter (Female pins) Allows RS 232 port to be connected to a PC (personal com-
puter). (Supplied in KIT 219-0436.) 142-0506
(L-COM RA098F)
15-pin DSUB Connector Mating connector for Analog input connector A2A5J6
Dsub 15 pin hood
Dsub 15 pin male
108-0374
(Tyco-Amp 207470-1)
142-0449
(Amphenol 17S-DA15P)
IDC 6-pin connector Mating connector for RS-232 PORT, connector A1J5 and PRO-
TECTION EXT. PORT, connector A2A5J7 142-0536
(Amphenol 5-555176-3)
IDC 8-pin plug Mating connector for PAR/SER PROTECT PORT (IN and
OUT) connectors. 142-0535
(Amphenol 5-555176-3)