KEPCO BHK-MG 40W (Half Rack) Series - Manual (Page 143)

BHK-MG 1/2 (OPR) 121313
B-17
Description: Sets selected power supply GPIB address. (See PAR. 3.3.5.2 and Figure 3-2 for special program-
ming considerations.)
B.70 SYSTem:COMMunication:GPIB:ADDRess? QUERY
SYST:COMM:GPIB:ADDR?
Syntax: Short Form: SYST:COMM:GPIB:ADDR?
Long Form: SYSTem:COMMunication:GPIB:ADDRess?
Return Value: 1 to 31
Description: Returns selected power supply GPIB address.
B.71 SYSTem:COMMunication:SERial:BAUD COMMAND
SYST:COMM:SER:BAUD
Syntax: Short Form: SYST:COMM:SER:BAUD {19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {19200 | 9600 | 4800 | 2400}
Description: Sets the unit to operate at the specified baud rate. (See PAR. 3.3.5.2 and Figure 3-2 for special
programming considerations.)
B.72 SYSTem:COMMunication:SERial:BAUD? QUERY
SYST:COMM:SER:BAUD?
Syntax: Short Form: SYST:COMM:SER:BAUD?
Long Form: SYSTem:COMMunication:SERial:BAUD?
Return Value: {19200 | 9600 | 4800 | 2400}
Description: Returns operating baud rate.
B.73 SYSTem:COMMunication:SERial:ECHO COMMAND
SYST:COMM:SER:ECHO
Syntax: Short Form: SYST:COMM:SER:ECHO {ON | OFF} or {01 | 00}
Long Form: SYSTem:COMMunication:SERial:ECHO {ON | OFF} or {01 | 00}
Description: Enables (ON or 01) or disables (OFF or 00) echo mode (see PAR. 3.5.3.1) Sending ON or 01
causes all subsequent characters to be echoed back. Sending OFF or 00 turns off the character echo
after the next line terminator character. The *RST command has no effect on echo status. (See PAR.
3.3.5.2 and Figure 3-2 for special programming considerations.)
B.74 SYSTem:COMMunication:SERial:ECHO? QUERY
SYST:COMM:SER:ECHO?
Syntax: Short Form: SYST:COMM:SER:ECHO?
Long Form: SYSTem:COMMunication:SERial:ECHO?
Return Value: {01 | 00}
Description: Returns 01 when echo mode is active (ON) or 00 when disabled (OFF) (see PAR. 3.5.3.1).
B.75 SYSTem:COMMunication:SERial:PACE COMMAND
SYST:COMM:SER:PACE
Syntax: Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}
Description: Enables (XON) or disables (NONE) data flow control via the serial interface. (See PAR. 3.5.3.3).
(See PAR. 3.3.5.2 and Figure 3-2 for special programming considerations.)
B.76 SYSTem:COMMunication:SERial:PACE? QUERY
SYST:COMM:SER:PACE?
Syntax: Short Form: SYST:COMM:SER:PACE?
Long Form: SYSTem:COMMunication:SERial:PACE?
Return Value: {01 | 00}
Description: Returns 01 when data flow control via the serial interface is enabled (XON) or 00 when disabled
(NONE) (see PAR. 3.5.3.3).
B.77 SYSTem:COMMunication:SERial:PROMpt COMMAND
SYST:COMM:SER:PROM
Syntax: Short Form: SYST:COMM:SER:PROM {ON | OFF} or {0 | 1}
Long Form: SYSTem:COMMunication:SERial:PROMpt {ON | OFF} or {0 | 1}