KEPCO BHK-MG 40W (Half Rack) Series - Manual (Page 10)

iv
BHK 1/2 RACK 121313
TABLE OF CONTENTS
SECTION PAGE
4.6 Changing the Calibration Password ....................................................................................................... 4-8
4.7 Restoring Previous Calibration Values ................................................................................................... 4-8
4.8 Restoring Factory Calibration Values ..................................................................................................... 4-8
4.9 Calibration Storage ................................................................................................................................. 4-9
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.1 Introduction ............................................................................................................................................. A-1
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-1
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-2
A.9 *RCL — Recall Command ...................................................................................................................... A-2
A.10 *RST — Reset Command....................................................................................................................... A-3
A.11 * SAV — Save Command....................................................................................................................... A-3
A.12 *SRE — Service Request Enable Command ......................................................................................... A-4
A.13 *SRE? — Service Request Enable Query .............................................................................................. A-4
A.14 *STB? — Status Byte Register Query .................................................................................................... A-4
A.15 *TRG — Trigger Command .................................................................................................................... A-4
A.16 *TST? — Self Test Query ....................................................................................................................... A-4
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 Numerical Values.................................................................................................................................... B-2
B.3 ABORt Command ................................................................................................................................... B-2
B.4 CAL Commands and Queries................................................................................................................. B-2
B.5 DISPlay:CONTrast Command ................................................................................................................ B-2
B.6 DISPlay:CONTrast? Query ..................................................................................................................... B-2
B.7 DISPlay:MODE Command ..................................................................................................................... B-4
B.8 DISPlay:MODE? Query .......................................................................................................................... B-4
B.9 DISPlay:TEXT Command ....................................................................................................................... B-4
B.10 DISPlay:TEXT? Query............................................................................................................................ B-4
B.11 INITiate[:IMMediate] Command.............................................................................................................. B-4
B.12 INITiate:CONTinuous Command ............................................................................................................ B-4
B.13 INITiate:CONTinuous? Query................................................................................................................. B-5
B.14 INSTrument:STATe Command ............................................................................................................... B-5
B.15 INSTrument:STATe? Query .................................................................................................................... B-5
B.16 [SOURce:]LIST:CLEar Command .......................................................................................................... B-5
B.17 [SOURce:]LIST:COUNt Command......................................................................................................... B-5
B.18 [SOURce:]LIST:COUNt? Query.............................................................................................................. B-5
B.19 [SOURce:]LIST:COUNt:SKIP Command................................................................................................ B-5
B.20 [SOURce:]LIST:COUNt:SKIP? Query .................................................................................................... B-6
B.21 [SOURce:]LIST:CURRent Command ..................................................................................................... B-6
B.22 [SOURce:]LIST:CURRent? Query.......................................................................................................... B-6
B.23 [SOURce:]LIST:CURRent:POINts? Query ............................................................................................. B-6
B.24 [SOURce:]LIST:DIRection Command..................................................................................................... B-6
B.25 [SOURce:]LIST:DIRection? Query ......................................................................................................... B-6
B.26 [SOURce:]LIST:DWELl Command ......................................................................................................... B-6
B.27 [SOURce:]LIST:DWELl? Query .............................................................................................................. B-7
B.28 [SOURce:]LIST:DWELl:POINts? Query ................................................................................................. B-7
B.29 [SOURce:]LIST:QUERy Command ........................................................................................................ B-7
B.30 [SOURce:]LIST:QUERy? Query ............................................................................................................. B-7
B.31 [SOURce:]LIST:VOLTage Command ..................................................................................................... B-7