KB Electronics KBDF-48 - Manual (Page 3)

3
TABLE OF CONTENTS (CONTINUED)
Table Page
1 Options ....................................................................................................................................13
2 General Performance Specifications.......................................................................................14
3 Electrical Ratings ....................................................................................................................15
4 Descriptions of 4-Digit Display, LEDs, Keys, and Potentiometer ............................................17
5 Drive Terminal Block Wire and Tightening Torque Specifications ..........................................22
6 Drive Multi-Function Input Terminal, Function, and Factory Code Assignment ......................25
7 Drive Input and Output Connections .......................................................................................26
8 Preset Frequency Selection ....................................................................................................37
9 Drive Multi-Function Output Relay "Run" and "Fault" Operating Modes.................................41
10 Digital Readout Codes ......................................................................................................52, 53
11 IODF Multi-Function Output Relay "Run" and "Fault" Operating Modes.................................64
12 IODF Input and Output Connections.......................................................................................65
13 IODF Terminal Block Wire and Tightening Torque Specifications ..........................................65
14 IODF Multi-Function Input Terminal, Function, and Factory Code Assignment......................66
Figure Page
1 Description of 4-Digit Display, LEDs, Keys, and Main Speed Potentiometer............................6
2 Maximum Allowed Motor Torque vs. Speed .............................................................................8
3 Drive Layout ............................................................................................................................16
4 Case "A" Drives Mechanical Specifications ............................................................................18
5 Case "B" Drives Mechanical Specifications ............................................................................19
6 General Connection Diagram..................................................................................................21
7 Models KBDF-13, 14, 16 AC Line Input and Ground Connections .........................................22
8 Models KBDF-23D, 24D, 27D AC Line Input and Ground Connections .................................23
9 Models KBDF-23, 23F, 24, 24F, 27, 27F AC Line Input and Ground Connections ................23
10 Models KBDF-23P, 24P AC Line Input and Ground Connections ..........................................23
11 Models KBDF-27P, 29 AC Line Input and Ground Connections.............................................23
12 Models KBDF-42, 43, 45, 48 AC Line Input and Ground Connections ...................................24
13 Motor and Ground Connections ..............................................................................................24
14 Automatic Start Connections and Drive Programming............................................................27
15 2-Wire Start/Stop Connections and Drive Programming.........................................................28
16 3-Wire Start/Stop Connections and Drive Programming.........................................................28
17 Forward/Stop and Reverse/Stop Connections and Drive Programming.................................29
18 Analog Input Signal Gain and Offset with Positive Slope (Low-to-High Signal)......................30
19 Analog Input Signal Gain and Offset with Negative Slope (High-to-Low Signal) ....................30
20 Analog Input Jumper J2 Settings ............................................................................................31
21 Voltage Following Connections, Jumper J2 Settings, and Drive Programming ......................31
22 Current Following Connections, Jumper J2 Settings, and Drive Programming ......................32
23 Unidirectional Remote Main Speed Potentiometer with Start/Stop
Connections, Jumper J2 Settings, and Drive Programming ...................................................33
24 Bidirectional Remote Main Speed Potentiometer with Start/Stop
Connections, Jumper J2 Settings, and Drive Programming ...................................................33
25 Unidirectional Remote Main Speed Potentiometer with Forward/Reverse
Connections, Jumper J2 Settings, and Drive Programming ...................................................34
26 Unidirectional Up/Down Frequency Control with 2-Wire Start/Stop
Connections, Jumper J2 Settings, and Drive Programming ...................................................35
27 Bidirectional Up/Down Frequency Control Connections and Drive Programming ..................36
28 Unidirectional Preset Frequency Selection with 2-Wire Start/Stop
Connections and Drive Programming .....................................................................................38
29 Unidirectional Preset Frequency Selection with 3-Wire Start/Stop
Connections and Drive Programming .....................................................................................38
30 Reset Connections and Drive Programming...........................................................................39
31 External Fault Connections and Drive Programming ..............................................................40