Extron Electronics FOX Matrix 14400 User Guide - Manual (Page 86)

Removing and Installing a Fan Module
The FOX Matrix 320x has four fan modules and the FOX Matrix 14400 has two fan modules.
The fan modules for each model are identical. If a fan fails, it should be replaced at the
earliest opportunity.
Removing a Fan Module
Remove a fan module as follows:
NOTE: The fans modules are hot-swappable. Either fan can be removed or installed
without powering down the switcher.
1. Remove and retain the two screws that secure the row identification plate to the fan
(see figure 50). Retain the plate.
ANAHEIM, CA
RESET
RS232/RS422
REMOTE
LAN
ACT LINK
100-240V 50/60Hz 1.2A MAX.
100-240V 50/60Hz 1.2A MAX.
REDUNDANT
PRIMAR
Y
PRIMAR
Y POWER SUPPL
Y
DISCONNECT BOTH POWE
R
CO RD S B EF OR E S ER VIC ING
REDUNDANT POWER SUPPL
Y
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T IN OU T
IN OUT
IN OU T IN OU T
IN OU T
IN OU T IN OU T
IN OU T
IN OU T IN OU T
IN OU T
IN OUT
IN OU T
IN OUT
IN OU T IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T
IN OU T IN OU T IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OUT
IN OU T
IN OUT
IN OUT
IN OUT
IN OU T IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T
IN OU T IN OU T
IN OU T
IN OU T IN OU T
IN OU T
IN OU T IN OU T
IN OU T
IN OUT
IN OU T
IN OUT
IN OUT
IN OU T
IN OU T
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OU T IN OUT
IN OUT
IN OUT
IN OUT
IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T
IN OU T
IN OU T IN OUT
IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OU T IN OUT
IN OUT
IN OU T
IN OU T
IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T
IN OU T
IN OU T IN OUT
IN OU T
IN OU T IN OU T
IN OU T
IN OUT
IN OU T
IN OU T
IN OUT
IN OU T
IN OU T
IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T
IN OU T IN OU T
IN OU T
IN OU T IN OU T
IN OU T
IN OUT
IN OU T IN OU T
IN OUT
IN OUT
IN OU T
IN OU T IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T IN OU T IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OU T IN OUT
IN OU T IN OUT
IN OU T
IN OUT
IN OU T IN OUT
IN OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU T IN OU T IN OU T
IN OUT
IN OU T IN OU T
IN OU T IN OU T IN OU T
IN OU T IN OUT
IN OU T
IN OUT
IN OU T IN OU T
IN OUT
IN
1 - 16
17 - 32
33 - 48
49 - 64
65 - 80
81 - 96
97 - 112
113 - 128
129 - 144
FAN ASSIMBL
Y
FAN ASSIMBL
Y
Align with
Plastic Guides
Remove 2 Screws
and Plate
Knurled
Knobs
Figure 50. Fan Replacement
2. Rotate the top and bottom knurled knobs to completely loosen the captive screws.
3. Gently pull on the screws to loosen the fan from the backplane.
4. Slide the fan out of the chassis.
FOX Matrix 320x and FOX Matrix 14400 • Maintenance and Modifications 80