Extron Electronics FOX Matrix 14400 User Guide User Manual
Page 34
Command and Response Table for SIS Commands (continued)
Command
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
View ties, mutes, and presets (continued)
View global preset
configuration
EX&
*
X@
*1VC
}
X!
n
•
X!
n+1
• ... •
X!
n+15
•Vid
]
Show the configuration of preset
X&
. Show the
input tied to 16 sequential outputs, starting
from output
X@
. n is the starting output number.
Command description:
preset # (
X&
)*starting output # (
X@
)*1VC
Response description:
input # (
X!
) tied to
X@
n
•
X!
tied to
X@
n+1
•
X!
tied to
X@
n+2
• ... •
X!
tied to
X@
n+15
•Vid
]
Example
(32 x 32 matrix):
E
23*25*1VC
}
Output:
Response = tied input:
input 2 tied to output 27
32
31
30
29
28
27
26
25
no tied input
input 8 tied to output 28
37 38 39 40
33 34 35 36
outputs do not exist
008•008•002•008•008•001•000•000
•Vid
•--•--•--•--•--•--•--•--•
Each position shown in the response is an output: left = output 25 (the starting output number), right = output 32.
(Outputs 33 through 40 are not present on this FOX matrix switcher.) The number in each position is the input
tied to that output.
In this example, video input 8 is tied to outputs 25, 26, 28, and 29; input 2 is tied to output 27; and input 1 is
tied to output 30. No inputs are tied to outputs 31 and 32.
NOTE:
EX&
*1*1VC
}
where
X&
= 0 returns the current video configuration of the switcher.
View room preset
configuration
EX*
*
X1)
*
X@
*1VC
}
X!
n
•
X!
n+1
• ... •
X!
n+15
•Vid
]
Show the configuration of room
X*
, preset
X1)
. Show the input tied to up to 16 outputs
assigned to room
X*
. n is the starting output
number.
Command description:
room # (
X*
)*room preset # (
X1)
)*starting output # (
X@
)*1VC
Response description:
input # (
X!
) tied to
X@
n
•
X!
tied to
X@
n+1
•
X!
tied to
X@
n+2
• ... •
X!
tied to
X@
n+15
•Vid
]
List input link detection
NOTE: The switcher reports the link status for only as many inputs as are supported by the highest numbered slot with an I/O board
installed. The switcher does not recognize gaps in the board installation. For example, if only two boards are installed, in slots 1 and 3,
leaving slot 2 empty, the switcher returns link status for 48 sequential inputs. The input link response for the inputs supported by the
board in slot 2, inputs 17 through 32, are all zeroes.
View all input connections
0LS
X1!
1
X1!
2
X1!
3
...
X1!
n
]
Each
X1!
response is the connection status of
all inputs, starting from input 1. n is the highest-
numbered installed input.
Example:
0LS
Input:
Response Status:
no input detected
input detected
1 2 3 4 5 6 7
n
0 0 0 1 1 1 0 . . . 0
NOTE
:
X!
= Input number (for tie)
00 – (maximum number of inputs for your configuration) (00 = untied)
X@
= Output number
01 – (maximum number of outputs for your configuration)
X1!
= Connection status
0 = no input connected 1 = input connected
X&
= Global preset #
00 – 64 (00 = current configuration for views only)
X*
= Room # (for room presets)
01 – 10 (each can have up to 10 presets (
X1)
s) assigned)
X1)
= Room preset #
01 – 10 maximum
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
28