Serial ports parameters, Sis command, Configure port timeout – Extron Electronics FOX Matrix 14400 User Guide User Manual
Page 40: Session must be in verbose mode 1 or 3 (see the, Verbose mode
Command
ASCII Command
(host to unit)
Response
(unit to host)
Additional description
IP setup commands (continued)
Set e-mail events for recipient
EX5#X5!
,
X5$
,
X5%
,0EM
}
Ipe
X5#X5!
*
X5$
*
X5%
*0
]
You must first have set an e-mail
recipient for the
X5!
variable, using
the separate
(CR) command on the previous page.
Example:
E
I69,63,3,0EM
}
IpeI69*63*3*0
]
E-mail account #69 (recipient #5,
JSmith), will receive fail/missing and
fixed/restored messages for input 63.
Read e-mail notifications for one
account (recipient)
EX5#X5!
,
X5$
EM
}
X5%X5%X5%
...
X5%
*0
]
Set DHCP on or off
EX5^
DH
}
Idh
X5^]
X5^
: 0 = off, 1 = on
Read DHCP on/off status
E
DH
}
X5^]
Set serial port parameters
EX5&
*
X5*
,
X5(
,
X6)
,
X6!
CP
}
Cpn
X5&
•Ccp
X5*
,
X5(
,
X6)
,
X6!]
Read serial port parameters
EX5&
CP
}
X5*
,
X5(
,
X6)
,
X6!]
Set serial port mode
EX5&
*
X6@
CY
}
Cpn
X5&
•Cty
X6@]
X6@
: 0 = RS-232, 1 = RS-422,
Read serial port mode
EX5&
CY
}
X6@]
Set verbose mode
EX6#
CV
}
Vrb
X6#]
Read verbose mode
E
CV
}
X6#]
Configure current port timeout
E
0*
X6$
TC
}
Pti0*
X6$]
View current port timeout
E
0TC
}
X6$]
Configure global IP port timeout
E
1*
X6$
TC
}
Pti1*
X6$]
View global IP port timeout
E
1TC
}
X6$]
SNMP setup commands
NOTE: See
, on page 68. This HTML page provides introductory information about Simple Network Management
Protocol (SNMP) and is the preferred method for performing the functions listed below.
Port mapping
Map SNMP port
E
A
X6%
PMAP
}
PmapA
X6%]
Assign a specific port.
Default:161.
Reset SNMP port to default
E
A161PMAP
}
PmapA00161
]
Disable SNMP port
E
A0PMAP
}
PmapA00000
]
Assign no port for SNMP.
Assign a valid port to enable.
View current SNMP port
E
APMAP
}
X6%]
Unit contact name and location
NOTE: No contact or location (as opposed to
Not•Specified, the default value) is not a valid entry.
Set unit contact info
E
C
X6^
SNMP
}
SnmpC*
X6^]
Set contact info to
X6^
.
Reset unit contact info to default
E
C•SNMP
}
SnmpC*Not•Specified
]
View unit contact info
E
CSNMP
}
X6^]
Set unit location info
E
L
X6^
SNMP
}
SnmpL*
X6^]
Set location info to
X6^
.
Reset unit location info to default
E
L•SNMP
}
SnmpL*Not•Specified
]
View unit location info
E
LSNMP
}
X6^]
Community names
Set unit read-only community name
E
P
X6&
SNMP
}
SnmpP*
X6&]
Set read-only (public) name to
X6&
.
Reset read-only community name
to default
E
P•SNMP
}
SnmpP*public
]
View unit read-only name
E
PSNMP
}
X6&]
Set unit read-write community name
E
X
X6&
SNMP
}
SnmpX*
X6&]
Set read-write (private) name to
X6&
.
Reset read-write community name
to default
E
X•SNMP
}
SnmpX*private
]
View unit read-write name
E
XSNMP
}
X6&]
Access enable
Enable SNMP access and traps
E
E1SNMP
}
SnmpE*1
]
Disable SNMP access and traps
E
E0SNMP
}
SnmpE*0
]
Default is disabled.
View SNMP access setting
E
ESNMP
}
X5^]
Command and Response Table for IP- and SNMP-Specific SIS Commands (continued)
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
34