Commands – Extron Electronics FOX Matrix 14400 User Guide User Manual
Page 39
X6$
= Port timeout (10-sec. increments)
1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
X6%
= SMNP port number
00000 (= disable) –
nnnnn. Default = 00161. Leading zeroes are not necessary for
entry.
X6^
= SNMP contact name and location
Up to 64 alphanumeric characters. Default = Not•Specified.
X6&
= SNMP community name
Up to 64 alphanumeric characters.
Default = public (for read community) or private (for read-write community).
X6*
= Trap target
1 – 3
X6(
= SNMP trap version
2 or 3, or 0 = empty (default) if no target set
X7)
= SNMP target 1 through 3
70 – 72. 70 = SNMP target 1, ... 72 = target 3
Command and Response Table for IP- and SNMP-Specific SIS Commands
Command
ASCII Command
(host to unit)
Response
(unit to host)
Additional description
IP setup commands
Set matrix name
EX4)
CN
}
Ipn•
X4)]
Read matrix name
E
CN
}
X4)]
Reset matrix name to factory
default
E
•CN
}
Ipn•
X4)]
“FOX-Matrix-” plus the last 3 pairs
of the MAC address.
Set time and date
EX4@
CT
}
Ipt
X4@]
Read time and date
E
CT
}
X4#]
Set GMT offset
EX4$
CZ
}
Ipz
X4$]
In the command, the divider between
hours and minutes can be either a
colon (:) or a period. In the response,
the divider is a colon.
Example:
E
8.0CZ
}
Ipz+08:00
]
Set Daylight Saving Time
EX4%
CX
}
X4%]
Read Daylight Saving Time
E
CX
}
X4%]
Set IP address
EX4^
CI
}
Ipi
X4^]
Read IP address
E
CI
}
X4^]
Read hardware address
E
CH
}
X4&]
Read # of open connections
E
CC
}
X4*]
Set subnet mask
EX4^
CS
}
Ips
X4^]
Read subnet mask
E
CS
}
X4^]
Set gateway IP address
EX4^
CG
}
Ipg
X4^]
Read gateway IP address
E
CG
}
X4^]
Set administrator password
EX4(
CA
}
Ipa•
X4(]
Read administrator password
E
CA
}
X4(]
Reset (clear) administrator password
E
•CA
}
Ipa•
]
Set user password
EX4(
CU
}
Ipu•
X4(]
Read user password
E
CU
}
X4(]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set mail server, domain name
EX4^
,
X5)
,
X4(
CM
}
Ipm
X4^
,
X5)
,
X4(]
Read mail server, domain name
E
CM
}
X4^
,
X5)
,
X4(]
Set e-mail recipient
EX5!
,
X5@
CR
}
Ipr
X5!
,
X5@
,
]
This command sets the e-mail
recipient. To receive e-mail notifications,
you must then set the events that the
switcher reports, using one or more
separate
(on the next page).
Example:
E
}
Ipr69,[email protected],
]
Read e-mail recipient or target
EX5!
CR
}
X5@
,
]
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
33