beautypg.com

Program editing steps – Niles Audio ZR-8630AVZR-8630AV User Manual

Page 77

background image

SOURCE-POWER EDITING
T

o edit the power commands for the source compo-

nents:

Step 1 - Press and hold the PROGRAM button.

The

PROGRAM LED lights, the TUNER 1/2 LED

lights, the

SEQUENCE LED blinks, and the ENTER IR

LED is on.

Edit Power for Source 3: T

ap the

NEXT button twice.

The

SOURCE

3/4

LED is RED, and the POWER OR

DISCRETE "ON"

LED blinks.

Skip to Step 2.

Edit Power for Source 4: T

ap the

NEXT button until

the

SOURCE 3/4 LED is GREEN and the POWER OR

DISCRETE "ON"

LED blinks.

Skip to Step 2.

Edit Power for Source 5: T

ap the

NEXT button until

the

SOURCE 5/6 LED is RED and the POWER OR

DISCRETE "ON"

LED blinks.

Skip to Step 2.

Edit Power for Source 6: T

ap the

NEXT button until

the

SOURCE 5/6 LED is GREEN and the POWER OR

DISCRETE "ON"

LED

blinks.

Skip to Step 2.

Edit Power for Source 7: T

ap the

NEXT button until

the

SOURCE 7/8 LED is RED and the POWER OR

DISCRETE "ON"

LED blinks.

Skip to Step 2.

Edit Power for Source 8: T

ap the

NEXT button until

the

SOURCE 7/8 LED is GREEN and the POWER OR

DISCRETE "ON"

LED blinks.

Skip to Step 2.

Step 2 - If the component has a single power IR com

-

mand for both ON and OFF, teach the power IR com-
mand by pressing the power button on the compo-
nent's factory remote.

or
If the component has discrete ON and OFF com

-

mands, teach the discrete ON command by pressing
the ON button on the source component's remote
control. The

ENTER IR LED blinks.

Step 3 - Immediately after capturing the IR

command,

test it by pressing the

TEST IR button. If the sour

ce

component does not respond correctly to the IR com-
mand, try reteaching the command at various dis-
tances from a half-inch (roughly a centimeter and a
quarter) to three feet (almost a meter).

Step 4 - T

ap the

NEXT button. The POWER ON LED

turns off and the

DISCRETE OFF LED blinks RED.

Step 5 - If the component has a single power com

-

mand for both ON and OFF, press the

NEXT button

again and continue to program the system.

or
If the component has a discrete ON and OFF com

-

mand, teach the discrete OFF command. The

ENTER

IR

LED blinks.

Step 6 - Immediately after capturing the IR command,
test it by pressing the

TEST IR button. If the sour

ce

component does not respond correctly to the IR com-
mand, try reteaching the command at various dis-
tances from a half-inch (roughly a centimeter and a
quarter) to three feet (almost a meter).

Step 7 -

Tap the

PROGRAM button to exit programming.

69

PROGRAM EDITING STEPS

IR COMMAND EDITING

T

o edit the individual IR commands for control of the

source components:

Step 1 - Press and hold the PROGRAM button.

The

PROGRAM LED lights, the TUNER

1/2

LED

lights, the

SEQUENCE LED blinks, and the ENTER IR

LED is on.

Edit IR Commands for Source 3: T

ap the

NEXT but

-

ton until the

SOURCE 3/4 LED is RED, and the IR

COMMANDS

LED blinks.

Skip to Step 2.

Edit IR Commands for Source 4: T

ap the

NEXT but

-

ton until the

SOURCE 3/4 LED is GREEN, and the IR

COMMANDS

LED blinks.

Skip to Step 2.

Edit IR Commands for Source 5: T

ap the

NEXT but

-

ton until the

SOURCE 5/6 LED is RED, and the IR

COMMANDS

LED blinks.

Skip to Step 2.