Panasonic TQBJ0350 - Manual (Page 89)

Technical Information
ENGLISH -
89
Appendix
Mode
Display resolution
(dots)
Scanning
frequency
Dot clock
frequency
(MHz)
Format
PnP *1
H
(kHz)
V
(Hz)
RGB2 DVI-D
EDID1
DVI-D
EDID2
DVI-D
EDID3 HDMI
1 280 Ч 800
1 280Ч800 41.3 50.0 68.0 D/H/R
1 280×800 49.7 59.8 83.5 D/H/R ○ *4 ○ *4 ○ *4 ○ *4
1 280×800 *3 49.3 59.9 71.0 D/H/R
1 280×800 62.8 74.9 106.5 D/H/R
1 280×800 71.6 84.9 122.5 D/H/R
MSXGA 1 280×960 60.0 60.0 108.0 D/H/R
SXGA
1 280×1 024 52.4 50.0 88.0 D/H/R
1 280×1 024 64.0 60.0 108.0 D/H/R ○ ○ ○ ○
1 280×1 024 72.3 66.3 125.0 D/H/R
1 280×1 024 78.2 72.0 135.1 D/H/R
1 280×1 024 80.0 75.0 135.0 D/H/R ○ ○ ○ ○
1 280×1 024 91.1 85.0 157.5 D/H/R
1 366 Ч 768
1 366Ч768 47.7 59.8 84.8 D/H/R
1 366×768 39.6 49.9 69.0 D/H/R
SXGA+
1 400×1 050 54.1 50.0 99.9 D/H/R
1 400×1 050 64.0 60.0 108.0 D/H/R
1 400×1 050 65.2 60.0 122.6 D/H/R ○ ○ ○ ○
1 400×1 050 65.3 60.0 121.8 D/H/R
1 400×1 050 78.8 72.0 149.3 D/H/R
1 400×1 050 82.2 75.0 155.9 D/H/R
WXGA+
1 440×900 55.9 59.9 106.5 D/H/R
1 440×900 46.3 49.9 86.8 D/H/R
UXGA60 1 600×1 200 75.0 60.0 162.0 D/H/R ○ ○ ○ ○
WSXGA+
1 680×1 050 65.3 60.0 146.3 D/H/R
1 680×1 050 54.1 50.0 119.5 D/H/R
1 920 Ч 1 080
1 920Ч1 080 55.6 49.9 141.5 D/H/R
1 920×1 080 *3 66.6 59.9 138.5 D/H/R
1 920×1 080 *5 67.2 60.0 173.0 R
WUXGA
1 920×1 200 61.8 49.9 158.3 D/H/R
1 920×1 200 *3 74.0 60.0 154.0 D/H/R ○ ○ ○ *5 ○ *5
1 920×1 200 *5 74.6 59.9 193.3 R
Where marked “ *1 : ” signals indicates in Plug and Play is compatible with EDID of projector. Unmarked
signals in Plug and Play may also be compliant if input terminals are written in the format list. Where Plug
and Play is unmarked and nothing is written in the format list, difficulties in projecting image may occur even
when computer and projector appear to have same resolution.
If a signal of 1 125 (1 035)/60i is input, it will be displayed as a signal of 1 125 (1 080)/60i. *2 :
VESA CVT-RB (Reduced Blanking) compatible. *3 :
PT-DW530E only *4 :
PT-DZ570E only *5 :
Some loss of data occurs to make projection easier. *6 :
Note
The number of display dots of the PT-DZ570E is 1 920 × 1 200, and the number of display dots of the PT-DW530E is 1 280 z
× 800, and the number of display dots of the PT-DX500E is 1 024 × 768.
A signal of a different resolution than the above data is converted to the number of display dots and then displayed.
The “i” appearing after the resolution indicates an interlaced signal. z
Flicker (line flicker) may be caused in images if interlace is connected. z