Sonance DAB1 - Manual (Page 22)

22
DAB1 DISTRIBUTED AUDIO SYSTEM
DAB1 Keypad
(see Figure 22)
The DAB1 Keypad lets you select the active source and control
the zone’s volume and muting, as well as providing a Z
ONE OFF
button and a built-in IR receiver.
The Z
ONE OFF button’s LED color indicates the zone’s status:
RReedd:: Zone is OFF (DAB1 is receiving power)
G Grreeeenn:: Zone is ON
O Orraannggee:: Built-in IR receiver is receiving IR commands
((ffllaasshhiinngg)) or a keypad button is being pressed. This occurs
even if the Zone is turned OFF
Each keypad button has three different actions: P RESS , P RESS -
A ND -H OLD and D OUBLE -P RESS . This allows each button to issue
three distinct commands or macros. Out-of-the-box the follow-
ing button functions are available on the Main Keypad:
V
V O O LL U U M M EE U UPP//D DO OW WN N BBuuttttoonnss:: P RESS = Volume UP/Down
M M
U U TT EE
BBuuttttoonn:: P
RESS = Mute/un-Mute the local zone; P RESS -A ND -
H OLD = Mute/un-Mute all zones designated for PARTY MODE
(see Appendix 1: “Party Mode”, on page 54).
ZZ oo nn ee SS oo uu rr cc ee SS ee ll ee cc tt oo rr BB uu tt tt oo nn ss :: P RESS = Select that source in
the local zone; P RESS -A ND -H OLD = Select that source in all zones designated for PARTY MODE (see Appendix 1: “Party
Mode”, on page 54). Pressing a Source Selector button in a zone that is OFF will turn that zone ON.
ZZ
O O N N EE O OFFFF BBuuttttoonn:: Turns the local zone OFF; P RESS - AND -H OLD = Turns all zones OFF (see Appendix
1 on page 54 for information about turning-OFF all zones in systems with multiple DAB1s).
Additional P
RESS , P RESS -A ND -H OLD , D OUBLE -P RESS , source component control and macro trigger
functions require programming with the Sonance Control Manager software. The Sonance Control
Manager can also be used to change any of the above out-of-the-box button functions.
D A B 1 K e y p a d I R R e c e i v e r
The DAB1 keypad’s built-in IR receiver allows the included IR remote to control the local zone (see
DAB1 IR Remote Control, on page 25). The IR receiver also passes IR commands from 3rd-party IR
remotes to IR emitters that are connected to the C
OMMON IR Outputs (see IR Connections, on page
15). The IR Receiver can be enabled or disabled via a rear-panel jumper (see Figure 23).
D A B 1 K e y p a d B a c k l i g h t i n g J u m p e r
The DAB1 keypad has a rear-panel Backlight Jumper ( Figure 24) that allows you to adjust
the amount of keypad backlighting to suit room lighting conditions and user preference.
Position 1 = DIM; Position 2 = BRIGHT; remove the jumper to turn the backlight OFF.
NOT E : Un l e s s t h e b a c k l i g h t j u m p e r i s re m o v e d , t h e k e y p a d b a c k l i g h t i n g i s
a l w ay s O N , e v e n i f t h e l o c a l z o n e a n d a l l z o n e s a re O F F .
34 1 25
DAB1 Keypad
Front Panel
67 8
5. Zone Source Selector Buttons
(Source 1 – Source 4)
6. Keypad Backlight Jumper
7. RJ45 Connection Jack
8. Keypad IR Receiver
ON/OFF Jumper
DAB1 Keypad
Rear Panel
1. Zone Mute Button
(Center of UP/DOWN)
2. Zone Volume UP/DOWN Buttons
3. Zone OFF Button
4. Zone IR Receiver
Figure 22: DAB1 Keypad
OFF ON
IR RECEIVER
OFF ON
IR RECEIVER
OFF ON
Figure 23:
DAB1 Keypad IR
Receiver Jumper
1 2 1 2 1 2
DIM OFF BRIGHT
Figure 24: DAB1 Keypad
Backlight Jumper