Sun Microsystems Netra 120 User Manual
Sun fire, V120 and netra, 120 server user’s guide
This manual is related to the following products:
Table of contents
Document Outline
- Sun Fire™ V120 and Netra™ 120 Server User’s Guide
- Contents
- Figures
- Tables
- Introduction
- 1.1 Overview of the Sun Fire V120 and Netra 120 Servers
- 1.2 Contents of the Ship Kit
- 1.3 Optional Hardware and Software
- 1.4 Front Panel
- 1.5 Back Panel
- 1.6 The Fans Inside the Sun Fire V120 and Netra 120 Servers
- 1.7 Tools You Need for Installation
- 1.8 Environmental Specifications
- 1.9 Choosing Between a Rack and a Cabinet
- Power and Cooling
- Using DC Power
- Installing Optional Hardware Components
- Installing the Server Into a Rack
- Connecting the Cables
- Powering On the Sun Fire V120 or Netra 120 Server
- Managing the Server From the lom> Prompt
- 8.1 Introduction to Lights-Out Management
- 8.2 Powering On or Resetting the Server From the LOM Shell
- 8.3 Monitoring the Server From the LOM Shell
- 8.4 Setting Up LOM Privileges for Named Users
- 8.4.1 Permission Levels Available for LOM Users
- 8.4.2 Creating a LOM User Account
- 8.4.3 Specifying the Password for a LOM User Account
- 8.4.4 Viewing Details of a LOM User Account
- 8.4.5 Changing Your Own User Password
- 8.4.6 Deleting a LOM User Account
- 8.4.7 Specifying Permissions for a Named User
- 8.4.8 Quitting a LOM Named User Session
- 8.5 Setting the LOM Device’s Configurable Variables
- 8.6 Separating the LOM From the Console on the Serial A/LOM Port
- 8.7 Viewing the Event Reports That the LOM Sends to syslogd
- 8.8 The LOM Shell Command List
- 8.9 Checking the Status of the Server’s Fans
- Managing the Server From the Solaris Prompt
- 9.1 Monitoring the System From Solaris
- 9.1.1 Viewing Online LOM Documentation
- 9.1.2 Checking the Power Supply Unit (lom -p)
- 9.1.3 Checking the Fans (lom -f)
- 9.1.4 Checking the Supply Rail Voltages and Internal Circuit Breakers (lom -v)
- 9.1.5 Checking the Internal Temperature (lom -t)
- 9.1.6 Checking the Status of the Fault LED and Alarms (lom -l)
- 9.1.7 Changing the LOM Automatic Server Restart Configuration (lom -w)
- 9.1.8 Viewing the Configuration of the LOM Device (lom -c)
- 9.1.9 Viewing All Component Status Data With the LOM Device’s Configuration Data (lom -a)
- 9.1.10 Viewing the Event Log (lom -e)
- 9.2 Configuring Automatic Server Restart (ASR)
- 9.3 Other LOM Tasks You Can Perform From Solaris
- 9.3.1 Turning Alarms On and Off (lom -A)
- 9.3.2 Turning the Fault LED On and Off (lom -F)
- 9.3.3 Changing the First Character of the Sequence for Escaping to the lom> Prompt (lom -X)
- 9.3.4 Stopping the LOM from Sending Reports to the Serial A/LOM Port (lom -E off)
- 9.3.5 Making the LOM Interface Backward Compatible (lom -B)
- 9.3.6 Upgrading the LOM Firmware (lom -G filename)
- 9.1 Monitoring the System From Solaris
- Troubleshooting
- Replacing a Server or Replacing Individual Components
- 11.1 Replacing a Server
- 11.2 Field Replaceable Units
- 11.3 Replacing the Memory Card Reader for the System Configuration Card
- 11.4 Replacing the DVD or CD-ROM Drive, Cable, and Paddleboard
- 11.5 Replacing the NVRAM Chip
- 11.6 Replacing the System Board
- 11.7 Replacing the Power Supply Unit
- 11.8 Replacing the Rear Fan Subassembly (Fans 1 and 2)
- 11.9 Replacing Fan 3
- Installing and Removing a SCSI Hard Disk Drive with Solaris Running
- Configuring the LOM Device Driver
- System Board Jumper Settings
- Introduction
- Index