IBM TM7 User Manual
Dbcs user’s guide
Table of contents
Document Outline
- Contents
- Preface
- Summary of Changes
- Figures
- Tables
- Part 1. General Information
- Chapter 1. Introduction
- Printer Overview
- Description of Models
- Planning Information
- Chapter 2. Installation Instructions
- Chapter 3. SureMark Installation, Service, and Utility Software
- Software Adjustments (Models TI5 and TG5 Only)
- 4610 DBCS Installation Utility Diskette
- DBCS Code Page Download
- DBCS User-Defined Character Download
- Firmware Update
- Emulating the IBM Model 3 or Model 4 Printers
- Emulating an Epson Single-Station Printer (Single-Station SureMark Only)
- Changing the Printer Mode between DBCS and SBCS
- Proportional Font Conversion Utility
- Resources on the Internet
- Part 2. Models TI5 and TG5
- Chapter 4. Operation (Models TI5 and TG5)
- Chapter 5. Testing and Problem Analysis – Models TI5 and TG5
- Part 3. Models TF7 and TM7
- Chapter 6. Operation (Models TF7 and TM7)
- Chapter 7. Testing and Problem Analysis – Models TF7 and TM7
- Part 4. Appendixes
- Appendix A. Consumable Supplies
- Appendix B. Technical Information
- Appendix C. RS-232 Programming Information
- RS-232 Commands Summary by Function
- Alphabetized RS-232 Commands Summary
- System Commands
- Preset or Onetime-Set Commands
- Download Graphics (Logo) Commands
- Predefine Messages
- Download User-Defined Characters
- Download Double-Byte Characters
- Flash Storage Write
- Erase Flash EPROM Sector
- Send Checksum of Flash EPROM Sector
- Microcode Tolerance (MCT) Information - Loading
- Microcode Tolerance (MCT) Information - Request
- DBCS Address Vectors
- Setup Commands
- Set Print Mode
- Set or Cancel Double-Wide Mode
- Set or Cancel Double-High Mode
- Set or Cancel Underline Mode
- Set or Cancel Overline Mode
- Set or Cancel Invert Mode
- Set or Cancel Emphasized Printing
- Set or Cancel High Quality Print Mode
- Set Print Station
- Select User-Defined or Resident Character Sets
- Set Code Page
- Set Inter-Character Spacing
- Set Inter-Character Spacing – DBCS
- Set or Cancel Rotated Characters
- Set Print Station Parameters
- Select 1/8-Inch Line Spacing
- Select 1/6-Inch Line Spacing
- Select Color Printing
- Set Line Spacing Using Minimum Units
- Set Sheet Eject Length
- Set Horizontal Tab Positions
- Set Left Margin Position
- Set Relative Position
- Align Positions
- Set or Cancel Unidirectional Printing
- Set Error Recovery Function
- Define Document Wait Time
- Status Sent to System
- Select Character for Reprinted Lines
- Reinitialize the Printer
- Enable or Disable the Feed Buttons (Models TI5 and TG5 Only)
- Enable or Disable the Beeper (Models TF7 and TM7 Only)
- Enable or Disable Upside-Down Printing
- Select Character Size for Scalable Fonts
- Fix Font Matrix
- Print Logo Inline
- Enable or Disable Two-Color Printing
- Bar Code Commands
- Print Character Commands
- Print Graphic Messages
- Miscellaneous Commands
- Asynchronous (Real-Time) Commands
- Data Buffer Management and Batch Printing
- Document Handling
- Appendix D. Uploading Electronic Journal Data
- Appendix E. Proportional Fonts
- Appendix F. Emulation Support for Epson Single-Station Printer
- Appendix G. Notices
- Electronic Emission Notices
- Federal Communications Commission (FCC) Statement
- Industry Canada Class A Emission Compliance Statement
- Avis de conformité aux normes d'Industrie Canada
- European Union (EU) Mark of Conformity Statement
- Japanese Voluntary Control Council for Interference (VCCI) Statement
- Korean Communications Statement
- Chinese Class A warning statement
- Taiwanese Class A Warning Statement
- Australia / New Zealand Compliance Statement
- Trademarks
- Electronic Emission Notices
- Index
- Readers’ Comments — We'd Like to Hear from You