D8b manual • appendices • page 168 – MACKIE Digital 8Bus D8B v5.1 User Manual
Page 174
D8B Manual • Appendices • page 168
D8B
Button
Number
D8B Button
Mapped HUI Button
Global
Mode
General HUI Layer
Comments
Pro Tools Function
Fader 17-24
Fader 1-8
N
Move corresponding PT channel Fader
Channel V-Pot
17-24
Channel V-Pot 1-8
N
Move corresponding PT channel Pan or Send Level
Mute 17-24
Mute 1-8
N
Mute corresponding PT channel
Solo 17-24
Solo 1-8
N
Solo corresponding PT channel
Select 17-24
Select 1-8
N
Select corresponding PT channel
Record Ready
17-24
Record Ready 1-8
N
Record Arm corresponding PT channel
Assign 17-24
VSel 1-8
N
Toggle Pre/Post of corresponding PT channel Send for selected Send A-E. If Level To Tape (HUI Aux Mute) is lit,
then it will toggle the mute status of the corresponding PT channel send for the selected Send A-E.
Alt+Assign 17-
24
Insert 1-8
N
Select corresponding PT channel for Insert Editing in VFD
Write 17-24
Auto 1-8
N
Use in conjunction with Auto Mode values to set automation mode for corresponding PT channel
1
Level to Tape
Aux Mute
N
When lit, assign (V-Sel) toggles the mute status of the selected Send. When not lit, V-Sel will toggle the selected Send Pre/Post.
2
Digital Trim
Shift (flip)
N
Puts HUI layer into shift Mode. Faders now adjust selected Aux Level, V-Pots adjust Aux Pan if available.
3
Aux 1
Send A
N
Enables control of PT Send A by HUI layer V-Pots
4
Aux 2
Send B
N
Enables control of PT Send B by HUI layer V-Pots
5
Aux 3
Send C
N
Enables control of PT Send C by HUI layer V-Pots
6
Aux 4
Send D
N
Enables control of PT Send D by HUI layer V-Pots
7
Aux 5
Send E
N
Enables control of PT Send E by HUI layer V-Pots
8
Aux 7
Rec Ready All
N
Enables all Rec Ready buttons in PT mixer
9
Aux 9-10
Bank Left
N
Shifts HUI layer to left by 8 to view previous 8 faders
10
Aux 11-12
Bank Right
N
Shifts HUI layer to right by 8 to view next 8 faders
11
Aux 9-10 Pan
Channel Left
N
Shifts HUI layer to left by 1 to view previous fader
12
Aux 11-12 Pan
Channel Right
N
Shifts HUI layer to right by 1 to view next fader
13
Pan
Pan
N
Enables control of PT Pan on HUI layer V-Pots
14
Shift
N
N/A
Shift + Masters
N/A
Y
Go to HUI Layer on
D8B
Go to HUI layer on D8B
D8B VFD Display
N
Displays Plug-in/Insert settings for selected Insert Channel. There are two main views: Plug-in Edit View and Insert Assign view.
Changes the assigned Plug-in, chooses a Plug-in Preset, or adjusts a plug-in parameter listed in bottom line of VFD.
D8B VFD V-Pots
N
Alt+Right D8B
VFD V-Pot
Scroll
N
Scroll to next/previous page of plug-in parameters in Plug-in Edit View. Scroll to inserts 1-4/5 in Insert Assign View.
D8B VFD Select
Buttons
N
Toggle Plug-in Parameter listed in top line of VFD in Plug-in Edit view
Previous / Next
N/A
N
Change between normal HUI VFD mode and channel HUI VFD Mode. See note below.
15
On
Assign
N
Enters Insert Assign Mode. When lit, turn a VFD V-Pot to change insert’s assigned Plug-in.
Press the corresponding VFD Select button to choose.
16
Setup
Compare
N
Toggles the Plug-In Compare button for Active Plug-in
17
Memory A
Bypass
N
Toggles the Bypass button for Active Plug-in
18
Memory B
Insert
N
Toggles between Plug-in Edit view and Insert Assign View
19
EQ
Window Transport
N
Opens/Closes PT Transport Window
20
Gate
Window ALT
N
Opens/Closes selected PT plug-in window
21
Compressor
Window Edit
N
Shows PT Edit Window
22
Plug-ins
Window Status
N
Opens/Closes PT Session Setup Window
23
Load Patch
Window Mix
N
Shows PT Mix Window
24
Save Patch
Window Mem Loc
N
Opens/Closes PT Memory Locate Window
25
Assign Bus 2
Auto Enable Send
N
Auto Arms Send Level in PT Auto Enable Window
26
Assign Bus 3
Auto Enable Plug-in
N
Auto Arms Plug-In in PT Auto Enable Window
27
Assign Bus 4
Auto Enable Send
Mute
N
Auto Arms Send Mute in PT Auto Enable Window
28
Assign Bus 5
Auto Mode Read
N
Hold and press a channel Write (HUI Auto) button to put the PT channel into Auto Read Mode
29
Assign Bus 7
Auto Mode Latch
N
Hold and press a channel Write (HUI Auto) button to put the PT channel into Auto Latch Mode
30
Assign Bus 8
Auto Mode Write
N
Hold and press a channel Write (HUI Auto) button to put the PT channel into Auto Write Mode
31
Assign L-R
Shift/Add
N
Shifts to second function of some buttons. Used to select multiple values of some parameters.
32
Assign Route To
Tape
Save
N
Press twice to save the open PT session
33
Automation
Bypass
Auto Mode Off
N
Hold and press a channel Write (HUI Auto) button to turn off PT automation on the channel
34
Automation
Faders
Auto Enable Fader
N
Auto Arms Volume in PT Auto Enable Window
Last Updated: 2/07/03
16220 Woodinville Redmond Rd. NE Woodinville, WA 98072
Tel: 800-258-6883 Fax: 425-806-6312 e-mail: [email protected]
D8B v5.1 B445 HUI Layer Control Mapping
For Pro Tools