Teac SS-R05 - Manual (Page 23)

5 − Playback
TASCAM SS-R1
Specifying a track number
You can use the remote’s numeric keys ( 0–9 ) to directly
specify the number of the track you want to play.
1 Use the remote’s numeric keys ( 0–9 ) to enter a
track number (maximum of three digits).
Enter the track number starting with the highest digit.
To specify track 1
Press the 1 key once.
To specify track 12
Press the 1 key ∑ 2 key.
To specify track 103
Press the 1 key ∑ 0 key ∑ 3 key.
•
•
•
2 Press the PLAY key.
The selected track will begin playing.
Alternatively, you can use this procedure but press the
remote’s
READY key instead of the PLAY key to pause
at the beginning of the selected track.
NOTE
As an alternative to press the PLAY key, you can
use the MULTI JOG dial to playback the file select-
ed (or the remote’s ENTER key).
You can’t use the numeric keys to specify the track
while in program or random mode. •
•
Fast-forward/rewind search
You can rapidly search forward or backward while listen-
ing to the audio of a track.
1 Play or pause the desired track.
2 Hold down the ˚ or ∆ key.
Fast-forward or rewind search will begin.
3 To stop searching, release the key you were hold-
ing.
You will return to the state (either playing or paused) in
which you were prior to searching.
Time search
While the unit is stopped, playing, or paused, you can
locate to a specified time in the specified track.
NOTE
You can’t use time search when the play mode is
program mode or random mode.
1 Use the remote’s numeric keys ( 0–9 ) to enter nine
digits in the following order.
Track number: three digits
Elapsed time from the beginning of the track
(
XX
hours /
XX
minutes /
XX
seconds): two digits each
For example if you want to locate to 1 minute 30 seconds
from the beginning of track 2, you would press the keys in
the following order.
0 ∑ 0 ∑ 2 ∑ 0 ∑ 0 ∑ 0 ∑ 1 ∑ 3 ∑ 0
•
•
When you finish entering the nine digits, the SS-R1 will
automatically locate to the specified position.
If the unit is stopped or playing back prior to the locate
operation, playback will begin after the locate operation. If
the unit is paused prior to the locate operation, it will pause
after the locate operation.
NOTE
If you specify a track number that does not exist in
the current play area, or a time that does not exist in
the track, the operation will be cancelled at that
point.
Time searching from an incomplete entry
If you press the remote’s ENTER key (or the PLAY or
READY key) before you finish entering all nine digits (to
the seconds place), the unit will locate to the position
you’ve specified so far.
For example if you enter “0
∑ 0
∑ 2 ∑ 0 ∑ 0 ∑ 1 ∑ 2” and press the ENTER key, the
recorder will locate to a position 12 minutes from the
beginning of track 2.
After the locate operation, the unit will either play or
pause, depending on the status prior to pressing the
ENTER
key. If you press the PLAY key, playback will begin. If you
press the READY key, the recorder will pause.
NOTE
This method allows you to omit the leading 0 of
the last place you enter (track, hour , minute), even
the leading 00 of the track number. For example if
you want to locate to minute 2 of track 2, press “0
∑ 0 ∑ 2 ∑ 0 ∑ 0 ∑ 2” and press the ENTER key.
If you enter only the track number and press the
ENTER key (or the PLAY key or READY key), the
result is the same as “Specifying the track number”
(page 23).
•
•