ADLINK aTCA-N700 User Manual
Page 60

aTCA-N700 SW Users Guide
54
nbm-robo trunk init
- initialize trunking
Following example shows how to enable a port and perform connection verification
such as ping operation.
root@aTCA-N700:~# nbm-robo show
Switch State: Managed (Forwarding)
Port Name STP Link Speed Tx(U) TX(B) Tx(M) Rx(U) RX(B) Rx(M)
0 IPMC DIS Up 100(H) 0 0 12 0 0 0
1 LMP DIS Up 1000(F) 0 0 0 0 41 6
2 FRONT DIS Up 1000(F) 0 0 0 0 0 0
3 BaseB DIS Down 1000(F) 0 0 0 0 0 0
4 BaseA DIS Up 1000(F) 0 0 0 21 1266 738
5 NP(B) DIS Up 1000(F) 0 0 6 0 0 6
6 NP(T) DIS Up 1000(F) 0 0 0 0 0 6
[root@N700]$
nbm-robo enable 2
[root@N700]$
nbm-robo enable 4
[root@N700]$ nbm-robo show
Switch State: Managed (Forwarding)
Port Name STP Link Speed Tx(U) TX(B) Tx(M) Rx(U) RX(B) Rx(M)
0 IPMC DIS Up 100(H) 0 0 12 0 0 0
1 LMP
NOSTP
Up 1000(F) 0 0 0 0 41 6
2 FRONT DIS Down 1000(F) 0 0 0 0 0 0
3 BaseB DIS Down 1000(F) 0 0 0 0 0 0
4 BaseA
NOSTP
Up 1000(F) 0 0 0 21 1266 738
5 NP(B) DIS Up 1000(F) 0 0 6 0 0 6
6 NP(T) DIS Up 1000(F) 0 0 0 0 0 6
[root@N700]$
ifconfig eth1 90.0.0.2<= eth1: BASE switch port 1 connected with a LMP
interface
[root@N700]$
ping 90.0.0.1
PING 90.0.0.1 (90.0.0.1): 56 data bytes
64 bytes from 90.0.0.1: icmp_seq=0 ttl=64 time=3.097 ms
64 bytes from 90.0.0.1: icmp_seq=1 ttl=64 time=0.248 ms
64 bytes from 90.0.0.1: icmp_seq=2 ttl=64 time=0.229 ms
...
As a Base Switchdefault configuration, put all ports in vlan 1, and set port 1(SOL)
speed= 100M (Full).
[root@N700]$
nbm-robo init
[root@N700]$ nbm-robo show
Switch State: Managed (Forwarding)
Port Name STP Link Speed Tx(U) TX(B) Tx(M) Rx(U) RX(B) Rx(M)
0 IPMC DIS Up
100(F)
0 0 12 0 0 0
1 LMP NOSTP
Up 1000(F) 0 0 0 0 41 6
2 FRONT DIS Down 1000(F) 0 0 0 0 0 0
3 BaseB DIS Down 1000(F) 0 0 0 0 0 0
4 BaseA NOSTP Up 1000(F) 0 0 0 21 1266 738
5 NP(B) DIS Up 1000(F) 0 0 6 0 0 6
6 NP(T) DIS Up 1000(F) 0 0 0 0 0 6
[root@N700]$
nbm-robo vlan show 1
VID Untagged Ports Tagged Ports
==================================
1 0 1 2 3 4 5 IMP
Add or delete vlan.
[root@N700]$ nbm-robo vlan add 2 1 untag