Great Planes Spirit 100 Sailplane Kit - GPMA0550 - Manual (Page 3)

WARNING! THIS IS NOT A TOY!
The model you will build from this kit is not a toy' It is capable of serious bodily harm and property damage. IT IS
YOUR RESPONSIBILITY AND YOURS ALONE - to build this kit correctly, properly install all R/C components and to
test the model and fly it ONLY with experienced, competent help in accordance with all safety standards and common
sense as set down in the Academy of Model Aeronautics Safety Code It is suggested that you join the AMA to become
properly insured before you attempt to fly the model IF YOU ARE JUST STARTING R/C MODELING, CONSULT YOUR
LOCAL HOBBY SHOP OR WRITE TO THE ACADEMY OF MODEL AERONAUTICS TO FIND AN EXPERIENCED
INSTRUCTOR IN YOUR AREA.
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302-9252(800) 435-9262
INTRODUCTION
Congratulations! You now own a revolutionary sailplane
kit! A bold statement indeed, but no other sailplane kit has ever
been able to satisfy so many desires. No matter what your skill
level - rank beginner or national soaring champion you will enjoy
this kit from the moment you start construction.
Thank you for purchasing the Great Planes SPIRIT 100
sailplane.
Please inspect all parts carefully before starting to build!
If any parts are missing, broken or defective, or if you have
any questions about building or flying this airplane, please
call us at (217) 398-8970 and we'll be glad to help. If you are
calling for replacement parts, please look up the part num-
bers and the kit identification number (stamped on the end of
the carton) and have them ready when calling.
PRECAUTIONS
1. You must build the plane according to the plans and in-
structions. Do not alter or modify the model as doing so may
result in an unsafe or un-flyable model In a few cases the plans
and instructions may d i f f e r slightly from the photos In those in-
stances you should assume the plans and written instructions
are correct.
2. You must take time to build straight, true and strong.
3. You must use a proper R/C radio that is in first class
condition and meets or exceeds "1991 specs".
4. You must properly install all R/C and other components so
that the model operates properly on the ground and in the air.
5. You must test the operation of the model before the first and
each successive flight to insure that all equipment is operating,
and you must make certain the model has remained structurally
sound. Be sure to check the nylon clevises often, and replace if
they show signs of wear.
6. You must fly the model only with the competent help of a
well experienced R/C pilot if you are not already an experienced
and knowledgeable R/C pilot at this time.
Note: We, as the kit manufacturer, can provide you with
a top quality kit and great instructions, but ultimately the
quality and "flyabilily" of your finished model depends
on how you build it; therefore, we cannot in any way
guarantee the performance of your completed model, and
no representations are expressed or implied as to the
performance or safely of your completed model.
Remember: Take your time and follow directions to end up
with a well-built model that is straight and true.
OTHER ITEMS REQUIRED
0 Radio having at least 2 channels (a third channel is required
for optional spoilers and a 4 channel radio with 5 servos is
required for the advanced wing) A computer radio or compa-
rable radio with mixing capabilities may be used to achieve total
camber control and CROW type mixing
0 Monokote or other covering material (2 rolls)
0 Latex foam rubber padding (1/4" thick)
0 #64 rubber bands
0 Heavy duty hi-start or other launching device
0 BB's or lead shot for balancing
0 Thin but strong thread - 30 (2 - 4lb fishing line works great)
0 Pushrods (Sullivan #503 or equivalent)
0 Hinges
The optional spoilers also require:
0 2 - 36" lengths of 20-30 lb fishing line
0 2 - 36" lengths of 1/8 " plastic tubing
The advanced wing also requires:
0 Thin copper wire or similar (for wrapping flap linkage)
0 2 - 36" servo extensions (or equivalent)
0 2 or 3 -12" servo extensions
3