Waterworks Easton Classic Pressure Balance Control Valve Trim with Oak Lever Handles - Manual

Notes:
ï Ideal operating pressure: 40-50 PSI
ï Maximum static pressure: 80 PSI
ï Rough in depth: 2
3 /
8
" ± 1 /
2
"
ï Supply lines: 1 /
2
" copper, 5 1 /
2
" spread
2 5 /
8
"
1 /
2
"
5 /
8
"
1 /
2
"
shower
discharge
inlet
tub
discharge
3"
1 /
4
"
1 /
2
"
2 3 /
8
"± 1 /
2
"
5 1 /
2
"
min
3"
3 1 /
2
"
Optional Handle
5 7 /
8
"
Easton ® Pressure Balance
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON ® PRESSURE BALANCE(EASV82-K,83-K,84-K,85-K-TRIM + GUSV80-
ROUGH)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
W A T E R W O R K S ® 3/04
EASV82-K (trim)(metal lever handle) + GUSV80R(rough)
EASV83-K (trim)(white porcelain lever handle) + GUSV80R(rough)
EASV84-K (trim)(black porcelain lever handle) + GUSV80R(rough)
EASV85-K (trim)(oak lever handle) + GUSV80R(rough)
➢ This valve should be on-site prior to rough in which allows
the installer to visualize the installation.
➢ Inspect this product to assure you have all parts required for
proper installation.
➢ Check incoming water pressure; ideal operating pressure is
40-50 psi.The minimum is 25 psi and the maximum is 80 psi.
➢ Use only a strap wrench or protected/smooth-jaw wrench
on any finished surface.
ROUGH IN:
1. Make sure the valve body is positioned according to valve
markings so the inlets are situated with hot piped on the left
and cold piped on the right.
2. Remove and discard the wall mounting flange(T-177) located
beneath the tile shield.The dome cover(T-19) included will
not be used during the installation.
3. REQUIRED:Valve body rough-in depth is 2 3 /
8
" ± 1 /
2
" from
the centerline of the supplies/inlets to the face of the
finished wall. Install so the back side of the plaster shield
contacts the finished wall as indicated on the shield and
shown in Figure 1.
4. Run 1 /
2
" copper supply lines with a 5 1 /
2
" center spread to the
proper height of the valve inlets and be sure to secure all
piping and fittings.
5. Turn on the hot and cold supplies and then check for leaks.
VALVE OPERATION:
6. When the finished wall is complete, turn on the hot and
cold supplies and pull off the tile shield(T-176) and discard.
Both supplies must be on or the valve will not operate.
7. The handle(5) is for controlling temperature only, not
volume. Install the handle so it rests at 6 o-clock in the OFF
position and then turn the handle counter clockwise through
the cold position and then warm and stopping at the hot
position. If additional rotational friction is required to
maintain the handle position, tighten the packing nut(T-17).
8. Allow the valve to run in warm position for a few minutes
to completely flush the system. If system is quite dirty,
remove valve spindle to ensure proper flushing.
9. IMPORTANT:This valve is equipped with a limit stop
screw(T-34) to be used to limit the valve handle from being
turned to excessively hot water discharge temperatures.
10. Setting the limit stop screw: Open the valve to the
maximum desired temperature and then turn the limit stop
screw(T-34) in until it seats.
IMPORTANT:
➢
To ensure this product is installed properly, you must read and
follow these guidelines.
➢ The owner/user of this valve must keep this information for
future reference.
➢ The risk of scalding exists until the installer has properly set the
temperature high limit stop.
➢ This valve can be used as a tub/shower combination or as a
shower valve only. Do NOT substitute other accessories such
as a hand shower for the tub spout.
➢ This product must be installed by a professional contractor and
conform to all applicable codes.
➢ Refer to the specification and assembly drawings attached.Valves
are sold partially assembled but shown fully disassembled for
illustrative and service purposes only.
➢ If soldering any connections, remove cartridge to prevent
damage to seals.
gusv81R
gusv81R
gusv81R
gusv81R
gusv81R
9.14.07