Great Plains YP1630F-1670 Operator Manual User Manual
Operator, Manufacturing, inc

Manufacturing, Inc.
© Copyright 2012
Printed 2012-12-27
401-832M
EN
ORIGINAL INSTRUCTIONS
Operator
YP1630F-1630 and YP1630F-1670
12 m 2-Section Yield-Pro
®
Dry Fertilizer Planters
Read the operator manual entirely. When you see this symbol, the
subsequent instructions and warnings are serious - follow without
exception. Your life and the lives of others depend on it!
Illustrations may show optional equipment not supplied with standard unit or may
depict similar YP1625/A or PD8070 models where a topic is identical.
34460
This manual is related to the following products:
Table of contents
Document Outline
- Operator
- Table of Contents
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Wear Protective Equipment
- Avoid High Pressure Fluids
- Handle Chemicals Properly
- Keep Riders Off Machinery
- Use Safety Lights and Devices
- Transport Machinery Safely
- Shutdown and Storage
- Tire Safety
- Practice Safe Maintenance
- Safety At All Times
- Safety Decals
- Safety Reflectors and Decals
- 818-055C Slow Moving Vehicle Reflector
- 838-266C Red Reflectors
- 838-265C Amber Reflectors
- 838-267C Daytime Reflectors
- 818-323C (Option) Danger: Chemical Hazard
- 818-590C Danger: Crushing Hazard
- 838-599C Danger: Electrocution Hazard
- 848-583C Danger: Do Not Ride
- 818-045C Warning: Pinch-Crush
- 818-188C Warning: Excessive Speed
- 818-339C Warning: High Pressure Fluid Hazard
- 818-579C Warning: Pinch-Shear Hazard
- 818-580C Warning: Overhead Hazard
- 818-628C Warning: Confined Space
- 818-632C Warning: Fan Hazard
- 818-860C Warning: Moving Parts
- 848-392C Warning: Eye and Dust Hazards
- 848-575C Warning: Falling Hazard
- 848-576C Warning: Moving Parts
- 818-398C Caution: Tires Not A Step
- 818-578C Caution: Tire Pressure
- 838-995C Caution: General
- 858-011C Warning: Tire Pressure
- Introduction
- Preparation and Setup
- Operating Instructions
- Pre-Start Checklist
- Wing Lock Overview
- Unfolding the Planter
- Raising/Lowering Planter
- Folding the Planter
- Transporting
- Loading Materials
- Disabling Unused Drives
- Field Setup Checklist
- Monitor Operation
- Fan General Operating Information
- Marker Operation
- Field Operation
- Parking
- Storage
- Adjustments
- Setting Material Rates
- Marker Adjustments
- Row Implement Adjustments
- 30 Series Row-Unit Adjustments
- Troubleshooting
- Maintenance and Lubrication
- Maintenance
- Material Unloading and Clean-Out
- Treatment Meter Gate Calibration (Option)
- Meter Maintenance
- Exchanging Finger Sets
- Remove Meter Cover
- Remove Adjustment Lever
- Remove Brush Block
- Remove Corn Finger Set
- Remove Insert “A”
- Install Insert “C”
- Install Brushless Block
- Install Sunflower Finger Set
- Set Finger Set Torque
- Re-Install Corn Finger Set
- Meter Drive Adjustments
- Brush Meter Maintenance
- Seed Plate Maintenance
- Bleeding Hydraulics
- Marker Maintenance
- Chain Maintenance
- Seed Flap Replacement
- Lubrication
- Seed Lubricant
- Depth Gauge Wheel Arms
- Caster Arm Pivot
- Marker Section Hinges
- Marker Mount Hinge
- Parallel Pivot Arms
- Tool Bar Pivots
- Tongue Lift Cylinder Anchor Pin
- Tongue-Mainframe Pivot Pin
- Tongue Slide Roller
- Frame-Mounted Coulter Pivot
- Caster Wheel Pivot
- Drive Chains, Wing Ground Drives
- Drive Chains, Fertilizer Ground Drive
- Drive Chains, Variable Rate Gearbox
- Main Transport Wheel Bearings
- Gauge Wheel Bearings
- Frame-Mounted Coulter Hub
- Unit-Mounted Coulter Hubs (Option)
- Marker Disk Hubs
- Seed Lubricants
- Options and Accessories
- Appendix A - Reference Information
- Appendix C - Initial Setup
- Appendix D - Option Installation
- Index