Automated cutting speeds (continued), Nitrogen plasma / water secondary, Electrode tip shield cup pcm-150 torch head – Tweco 15XC CE Merlin PAK User Manual
Page 69
Manual 0-2529
3 - 35
OPERATION
Automated Cutting Speeds (continued)
NOTES:
1. Kerf widths are listed as the width of the cut at the bottom of the plate.
2. Speed, kerf width, voltage and standoff data represent realistic starting points. Adjustments may be
required to obtain optimum results.
3. The copper shield cup (9-5790) is recommended for general machine cutting. When the clear-the-plate
function of a height control is required, then the short copper shield cup (9-5801) is recommended.
4. NR in chart means piercing not recommended. Drill starting hole or edge start the cut.
Electrode
Tip
Shield Cup
PCM-150 Torch Head
A-03448
Stainless Steel
Argon-Hydrogen Plasma / Nitrogen Secondary
Heavy duty, extended electrode life, extra square, oxide free, reduced smoke
Plasma @ 60 psi (4.1 bar)
Secondary @ 60 psi (4.1 bar)
Nitrogen Plasma / Water Secondary
Economical, reduced oxides on cut face, improved squareness
Plasma @ 60 psi (4.1 bar)
Secondary @ 60 psi (4.1 bar)
Material Thickness
Tip
Electrode Output Volts Amperage Speed (Per Minute)
Standoff
Pierce Height
Pierce
inches
mm
Cat #
Cat #
vdc
Amps
inches
meters
inches
mm
inches
mm
Delay (Sec)
inches
mm
3/8
9.5
9-5767
9-5754
130
150
60
1.52
0.312
7.9
0.375
9.5
0.4
0.055
1.4
1/2
12.7
9-5767
9-5754
135
150
50
1.27
0.312
7.9
0.375
9.5
0.6
0.055
1.4
3/4
19.1
9-5767
9-5754
145
150
35
0.89
0.312
7.9
0.500
12.7
0.8
0.065
1.7
1
25.4
9-5767
9-5754
150
150
20
0.51
0.312
7.9
0.500
12.7
1.5
0.065
1.7
1 1/2
38.1
9-5767
9-5754
160
150
10
0.25
0.375
9.5
NR
NR
NR
0.093
2.4
2
50.8
9-5767
9-5754
170
150
6
0.15
0.375
9.5
NR
NR
NR
0.093
2.4
Kerf Width
Material Thickness
Tip
Electrode Output Volts Amperage Speed (Per Minute)
Standoff
Pierce Height
Pierce
inches
mm
Cat #
Cat #
vdc
Amps
inches
meters
inches
mm
inches
mm
Delay (Sec)
inches
mm
16 ga
1.5
9-5766
9-5754
100
100
250
6.35
0.125
3.2
0.187
4.7
0.1
0.035
0.9
14 ga
1.9
9-5767
9-5754
110
150
225
5.72
0.187
4.7
0.187
4.7
0.1
0.055
1.4
10 ga
3.4
9-5767
9-5754
115
150
200
5.08
0.187
4.7
0.187
4.7
0.1
0.055
1.4
7 ga
4.6
9-5767
9-5754
120
150
175
4.45
0.312
7.9
0.375
9.5
0.2
0.055
1.4
1/4
6.4
9-5767
9-5754
125
150
125
3.18
0.312
7.9
0.375
9.5
0.2
0.055
1.4
3/8
9.5
9-5767
9-5754
130
150
80
2.03
0.312
7.9
0.375
9.5
0.4
0.055
1.4
1/2
12.7
9-5767
9-5754
135
150
60
1.52
0.312
7.9
0.375
9.5
0.6
0.055
1.4
Kerf Width