Banner SureCross DX80 Wireless Networks - Manual (Page 14)

14
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross Wireless Network
Product Manual
Introduction
DX80 Node Setup Menus
When power is applied, the DX80 begins running. The display screen auto loops through the RUN menu and communication begins between
the Gateway and Node(s). Auto looping through the RUN menu is the normal operating mode for all devices on the wireless network.
From the RUN Menu (or any menu), single-click button 1 to advance through the top-level menus. The device auto display loops through the
menu options if either of the RUN, DINFO, or FCTRY menus are selected. If the device is paused on the DVCFG or DERR menu options, the
display does not auto display loop.
To enter manual scrolling mode, double-click button 2 at the top level menu. Use the instructions shown in the chart below to navigate the
menu system. To return to the top level menus and auto display loop mode, double-click button 2 twice.
* DINFO * RUN * FCTRY * DVCFG * DERR
AUTO
DISPLAY
LOOP
AUTO
DISPLAY
LOOP
AUTO
DISPLAY
LOOP
(DEV)
NOD XX
(NAME)
NODE XX
KIT
XXXXX
(NID)
XX
(DEV)
NOD XX
(RADIO
MICRO)
V 00.0 A
(DX80
S/N)
0x0000(2)
(LCD
MICRO)
0x0000(2)
(PROD
DATE)
(00-00)
Single-click
Button 2
NEW XX
Single-click
Button 2
Single-click
Button 2
SAVES NEW
VALUES
(NID)
Network ID
Single-click
Button 2
Double-click Btn 2
NEW XX
Single-click
Button 2
Single-click
Button 2
SAVES NEW
VALUES
(NADR)
Node Address
NOD XX
** EC XX IGNORE
* ERROR
Single-click Button 1
** LCD will display ‘NO ERR’ if no error is detected.
Single-click
Button 2
Single-click
Button 2
New Error
Detected
Single-click Button 2
OFF Press and hold Button 1 from any top level menu to power down the Node.
Press and hold Button 1 from power down mode to enter RUN mode.
ADJUST LEFT
ROTARY SWITCH
TO SET
NETWORK ID
ADJUST RIGHT
ROTARY SWITCH
TO SET
NODE ADDRESS
(DEV)
I/O XX
NOD XX
NID XX
ON/OFF
Single-click
Button 1
Single-click
Button 1
Single-click
Button 1
(DX80
MODEL)
0x0000(2)
0.00
Single-click Button 1 to advance through menu
MANUAL
AUTO
SET
Single-click
Button 2
Single-click B1
(XADR)
Extended Addressing
XADR
Adjust rotary switch
to set XADR
Single-click
Button 2
XXXXXX Single-click B1
CONFRM
XADR
XXXXX
NETWRK
Single-click
Button 2
BINDNG
Single-click
Button 1 or 2
Reboot
Double-click
Button 2
BOUND
Device Info Factory #s Device Config. Device Error
Single-click
Button 2
PRIOR
NADR
XX
NEW
NADR
XX
CONFRM
NADR
XX
Single-click Button 1 to advance through menu
Navigating the menu:
* indicates a top level menu option
( ) indicates a sub-menu item
No characters indicate the value of the
previous item
Node LCD Timeout: After 15 minutes of
inactivity, the LCD screen stops displaying
information. Press any button to refresh the
display if the Node has entered this energy-
saving mode.
The Network ID (NID) and
Node Address (NADR) can be
set at any time from the rotary
switches. The left rotary switch
sets the Network ID and the
right rotary switch sets the Node
Address.
The MAXN and XADR menus are only available in extended addressing mode. To access extended
addressing mode, move DIP switch 1 to the ON position. To manually select the serial number,
use button 1 to move across the digits and use the right rotary switch to select the value used as
the device serial number.