Maintenance, Maintenance 123 – MTS SWIFT 30 Sensor User Manual
Page 123
SWIFT 30 Sensors
Maintenance
123
Maintenance
Overview
This chapter contains scheduling guidelines and detailed instructions for
performing maintenance—a set of routine procedures that allow you to extend
the operating life of your transducer and the transducer interface electronics. You
can prevent excessive wear or possible component failure through regular
inspections and simple procedures, such as filter cleaning.
The information provided in this chapter is a recommendation only. The actual
time intervals will depend on the operating conditions at your facility.
Contents
Maintenance Schedule
A
CTIVITY
C
USTOMER
P
REVENTIVE
M
AINTENANCE
C
ONTACT
MTS
C
ALENDAR
T
IME
1 D
AY
1 W
EEK
1 M
ONTH
1 Y
EAR
S
UGGESTED
Inspect Transducer for cracks
X
Check Transducer Interface cooling
X
Clean Transducer Interface fan filter
X
Inspect electrical cables
X
Calibrate the Transducer
X
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)