KROHNE UFC 400 FOUNDATION FIELDBUS EN - Manual (Page 34)

4
OPERATION
34
UFC 400
www.krohne.com 05/2013 - 4002813701 - AD FF UFC 400 R01 en
FIELD_VAL FIELD_VAL FIELD_VAL FIELD_VAL
Field Value
R Raw value of the field device in percent of the PV range, with a
status reflecting the transducer condition, before signal
characterization (L_TYPE) or filtering (PV_FTIME).
-
Status R Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
Bad
Non Specific
Not Limited
Value R A numerical quantity entered by a user or calculated by the
algorithm.
0.0
GRANT_DENY GRANT_DENY GRANT_DENY GRANT_DENY
Grant Deny
Options for controlling access of host computers and local
control panels to operating, tuning and alarm parameters of
the block.
-
GRANT
Grant
R/W Depending on the philosophy of the plant, the operator or a
higher level device (HLD) or a local operator's panel (LOP) in
the case of "Local", may turn on an item of the "Grant"
attribute - "Program, Tune, Alarm or Local".
Uninitialized
Setting:
Program / Tune / Alarm / Local / Operate
DENY
Deny
R/W The deny attribute is provided for use by a monitoring
application in an interface device and may not be changed by
an operator.
Uninitialized
Setting:
Program denied / Tune denied / Alarm denied / Local denied /
Operate denied
HI_ALM HI_ALM HI_ALM HI_ALM
High Alarm
The status for High Alarm and its associated time stamp.
Settings of 5 subelements see in the following part.
-
HI_HI_ALM HI_HI_ALM HI_HI_ALM HI_HI_ALM
High High Alarm
Mix The status for High High Alarm and its associated time stamp.
Settings of 5 subelements see in the following part.
-
Settings of 5 subelements for previous 2 parameters High Alarm and High High Alarm:
Unacknowledged R/W Setting:
Uninitialized / Acknowledged / Unacknowledged
Uninitialized
Alarm State R Setting:
Uninitialized / Clear - reported / Clear - not reported / Active -
reported / Active - not reported
Uninitialized
Time Stamp R Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Uninitialized
Subcode R Setting:
Other / Block Configuration / Link Configuration / Simulation
Active / Local Override / Device Fault State / Device
Maintenance / Input Failure / Output Failure / Memory
Failure / Lost Static Data / Lost NV Data / Readback Check /
Maintenance Needed / Power Up / Out Of Service
Other
VALUE
Float Value
R A numerical quantity entered by a user or calculated by the
algorithm.
0.0
HI_HI_LIM HI_HI_LIM HI_HI_LIM HI_HI_LIM
High High Limit
R/W The setting for High High Alarm in engineering units.
Setting range see in the following part.
NaN
HI_HI_PRI HI_HI_PRI HI_HI_PRI HI_HI_PRI
High High Priority
R/W Priority of the High High Alarm.
Setting see in the following part.
0
HI_LIM HI_LIM HI_LIM HI_LIM
High Limit
R/W The setting for High Alarm in engineering units.
Setting range see in the following part.
NaN
HI_PRI HI_PRI HI_PRI HI_PRI
High Priority
R/W Priority of the High Alarm.
Setting see in the following part.
0
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value