KROHNE UFC 400 FOUNDATION FIELDBUS EN - Manual (Page 15)

OPERATION
4
15
UFC 400
www.krohne.com 05/2013 - 4002813701 - AD FF UFC 400 R01 en
Time Stamp R The time when evaluation of the block was started and a
change in alarm/event state was detected that is unreported.
The time stamp value will be maintained constant until alert
confirmation has been received - even if another change of
state occurs.
Uninitialized
Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Subcode R An enumeration specifying the cause of the alert to be
reported.
-
Value R The value of the associated parameter at the time the alert
was detected.
-
FD_FAIL_MAP FD_FAIL_MAP FD_FAIL_MAP FD_FAIL_MAP
Fail Map
R/W This parameter enables or disables conditions to be detected
as active for this alarm category.
(28) (29) (30) (31)
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process / (29) F
Configuration / (30) F Electronics / (31) F Sensor
FD_FAIL_MASK FD_FAIL_MASK FD_FAIL_MASK FD_FAIL_MASK
Fail Mask
R/W This parameter allows the user to suppress any single or
multiple conditions that are active, in this category, from
being broadcast to the host through the alarm parameter.
(28) (29) (30) (31)
Setting:
(00) Check / (01) Electronics : Operation Info / (08) Electronics
: Power Fail / (10) Configuration : Totaliser / (11) Process :
Signal Unreliable / (12) Process : Signal Lost / (13) Process :
Empty Pipe / (14) Electronics : IO Connection / (15) Process :
Current input / (16) M Process / (17) M Configuration / (18) M
Electronics / (19) M Sensor / (20) S Process / (21) S
Configuration / (22) S Electronics / (23) S Sensor / (24) C
Process / (25) C Configuration / (26) C Electronics / (27) C
Sensor / (28) F Process / (29) F Configuration / (30) F
Electronics / (31) F Sensor
FD_FAILK_PRI FD_FAILK_PRI FD_FAILK_PRI FD_FAILK_PRI
Fail Priority
R/W This parameter allows the user to specify the priority of this
alarm category.
0
Setting:
0...15
FD_EXTENDED_ FD_EXTENDED_ FD_EXTENDED_ FD_EXTENDED_
ACTIVE_1 ACTIVE_1 ACTIVE_1 ACTIVE_1
FD_EXTENDED_
ACTIVE_1
R An optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Optical Interf. Active / (01) Disp. 2 Overrange / (02) Disp. 1
Overrange / (06) RB is set to OOS / (07) Fieldbus No
Connection / (11) Status Out B Active / (13) Status Out A
Active / (14) Control In B Active / (15) Control In A Active / (30)
Sensor Starting up / (31) Zero Calibr. Running
FD_EXTENDED_ FD_EXTENDED_ FD_EXTENDED_ FD_EXTENDED_
ACTIVE_2 ACTIVE_2 ACTIVE_2 ACTIVE_2
FD_EXTENDED_
ACTIVE_2
R An optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(20) Disp. 2 no measure values / (21) Dsp. 1 no measure
values / (28) IO B No Value for Binary Output / (29) IO B No
Value for Current Output / (30) IO A No Value for Binary
Output / (31) IO A No Value for Current Output
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value