TREND NX Variable Speed Drives User Manual
Page 128
10 • vacon
Basic Application
Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205
1
1.4.2
Basic parameters (Control keypad: Menu M2
Æ
G2.1)
Code
Parameter
Min
Max
Unit
Default
Cus
t
ID
Note
P2.1
Min frequency
0,00
Par.
2.2
Hz 0,00 101
P2.2
Max frequency
Par.
2.1 320,00 Hz 50,00
102
NOTE: If f
max
> than the
motor synchronous speed,
check suitability for motor
and drive system
P2.3
Acceleration time 1
0,1 3000,0 s
3,0
103
P2.4
Deceleration time 1
0,1 3000,0 s
3,0
104
P2.5
Current limit
0,1 x I
H
2 x I
H
A I
L
107
P2.6
Nominal voltage of
the motor
180 690 V
NX2: 230V
NX5: 400V
NX6: 690V
110
Check the rating plate of
the motor.
P2.7
Nominal frequency
of the motor
8,00 320,00 Hz 50,00
111
Check the rating plate of
the motor.
P2.8
Nominal speed of
the motor
24 20
000
rpm 1440
112
Check the rating plate of
the motor.
The default applies for a 4-
pole motor and a nominal
size frequency converter.
P2.9
Nominal current of
the motor
0,1 x I
H
2 x I
H
A I
H
113
Check the rating plate of
the motor.
P2.10
Motor cos
ϕ
0,30 1,00 0,85
120
Check the rating plate of
the motor
P2.11
Start function
0 1 0
505
0=Ramp
1=Flying start
P2.12
Stop function
0 3 0
506
0=Coasting
1=Ramp
2=Ramp+Run enable
coast
3=Coast+Run enable
ramp
P2.13
U/f optimisation
0
1
0
109
0=Not used
1=Automatic torque boost
P2.14
I/O reference
0 3 0
117
0=AI1
1=AI2
2=Keypad
3=Fieldbus
P2.15
Current reference
offset
0 1 1
302
0= No offset, 0—20mA
1= Offset, 4mA—20 mA
P2.16
Analogue output
function
0 8 1
307
0=Not used
1=Output freq. (0—f
max
)
2=Freq. reference (0—
f
max
)
3=Motor speed (0—Motor
nominal speed)
4=Output current (0-I
nMotor
)
5=Motor torque (0—
T
nMotor
)
6=Motor power (0—
P
nMotor
)
7=Motor voltage (0-U
nMotor
)
8=DC-link volt (0—1000V)
P2.17
DIN3 function
0 7 1
301
0=Not used
1=Ext. fault, closing cont.
2=Ext. fault, opening cont.
3=Run enable, cc
4=Run enable, oc
5=Force cp. to IO
6=Force cp. to keypad
7=Force cp. to fieldbus
P2.18
Preset speed 1
0,00 Par.
2.1.2 Hz
0,00
105 Speeds preset by operator
P2.19
Preset speed 2
0,00 Par.
2.1.2 Hz 50,00
106 Speeds preset by operator