IAI America LSAS-N15HM - Manual (Page 73)

13. Replacement/Adjustment of Stainless Sheet
57
[3] Move the slider to check the tension of the stainless sheet over the entire stroke zone.
,I.H\&KHFN3RLQWV±DQGDUHQRWVDWLVILHGORRVHQWKHIL[LQJVFUHZVDJDLQand readjust the stainless
VKHHWSRVLWLRQDQGWHQVLRQIURPVWHS>@DERYH
1RWH ,IWKHUHDGMXVWPHQWRI.H\&KHFN3RLQW±FDQQRWEHSHUIRUPHGZHOOUHYHUVLQJWKHIURQWDQGUHDU
SRVLWLRQVRUIOLSSLQJWKHIURQWDQGEDFNVLGHVRIWKHVWDLQOHVVVKHHWPD\PDNHLWSRVVLEOHWR
readjust.
,IWKH\VWLOOIDLOUHSODFHZLWK a new stainless sheet.
[4] After the allocation of clearances and non- FRQWDFWZLWKWKHVOLGHU¶VPDLQERG\KDYHEHHQ
FRQILUPHGWLJKWHQWKHWZRVFUHZV on the loose side alternatively and finally clamp them with a
uniform torque. If the screws are tightened with
DQRQXQLIRUPWRUTXHWKHVWDLQOHVVVKHHWPD\
zigzag or float.
>@ 5HPRYHWKHFOHDUDQFHFKHFNMLJDQGWKHQPRXQWWKHUHJXODUVOLGHUFRYHUDQGPRWRUFRYHU
Caution) Be careful not to lose the coil springs during this procedure.
.H\&KHFN3RLQW±
&KHFNWKDWWKHFOHDUDQFHEHWZHHQWKHWRSVXUIDFHRIWKHVWDLQOess sheet and the top
surface of the slider is within the designated range over the entire stroke zone.
.H\&KHFN3RLQW±
Viewing through the outside
RSHQLQJVFKHFNWKDWWKH
edges of the stainless sheet GRQRWWRXFKWKHVOLGHU¶V
PDLQERG\&KHFNWKLVDWOHDVWIRUWKUHHURXQGWULSVWURNHV
over the entire stroke zone
7KHVWDLQOHVVVKHHWPD\EH
GLVSODFHGGXULQJURXQGWULSPRYHPHQWVEXWLIWKHHGJHV
WRXFKWKHVOLGHU¶VPDLQERG\ZLWKRXWLQFUHDVLQJWKH
GLVSODFHPHQWDPRXQWUHDGMXVWE\UHSHDWLQJIURPVWHS>@
DERYH
Note that the stainless sheet itself is not completely
VWUDLJKWDQGKDVVRPH]LJ]DJVWKXVLWLVQRWSRVVLEOHWR
make the right and left clearances uniform. There is no
SUREOHPDVORQJDVWKHHGJHVof the stainless sheet and
WKHVOLGHU¶VPDLQERG\GRQRWWRXFKHDFKRWKHURYHUWKH
entire stroke zone.
Make the clearance of this
part the same as the one
on the opposite side.
7LJKWHQWKHVFUHZVRQERWKVLGHVLQRUGHUWRIDVWHQWKHVWDLQHVVVKHHW
7LJKWHQLQJWRUTXH1˜FPNJI˜ cm)