Extron Electronics System 5 IP Series User Guide - Manual (Page 66)

SIS ™ Programming and Control, cont’d
System 5 IP • SIS ™ Programming and Control 5-10
PRELIMINAR
Y
Audio tr
eble adjustment (global: applies to all inputs)
Set the tr
eble level
X7
>
X7
%3E
T
rb
X7
Set the global tr
eble level.
X7
= 0 to 10,
-10 dB to +10 dB in 2 dB steps (0 = -10 dB, 1 = -8 dB, 2 = -6 dB,... 10 = +10 dB).
Example
:
2>
2%3E
T
rb02
Example
: set tr
eble to -6 dB.
Incr
ement an input’s tr
eble level
+ >
%2B%3E
T
rb
X7
Incr
ease the tr
eble by 2 dB.
Decr
ement an input’s tr
eble level
– >
%2D%3E
T
rb
X7
Decr
ease the tr
eble by 2 dB.
V
iew the tr
eble level
>
%3E
X7
Show the curr
ent tr
eble level.
Audio bass adjustment (global: applies to all inputs)
Set the bass level
X7
<
X7
%3C
Bas
X7
Set the global bass level.
X7
= 0 to 10, -10 dB
to +10 dB in 2 dB steps (0 = -10 dB, 1 = -8 dB, 2 = -6 dB,... 10 = +10 dB).
Incr
ement the bass level
+ <
%2B%3C
Bas
X7
Incr
ease the bass by 2 dB.
Decr
ement the bass level
– <
%2D%3C
Bas
X7
Decr
ease the bass by 2 dB.
V
iew the bass level
<
%3C
X7
Show the curr
ent bass level.
Audio mute (overall: amp and pr
eamp)
Mute on
1Z
1Z
Amt1
Mute all (Lineout/fixed, Pr
eamp/variable,
& amplified) audio outputs. This is
not
the
same as selecting input 0.
Mute of
f
0Z
0Z
Amt0
Unmute all audio outputs.
V
iew the audio mute status
Z
Z
X5
Show the status of audio mute. X5
= 0 (of
f/disable) or 1 (on/enable).
The 1Z mute command is not the same as selecting input 0.
Audio status for the active input
These commands allow you to view (or pr
ogram a contr
ol system to monitor) the on/of
f status of the Signal, Normal, and Clip ind
icators (the equivalent of viewing the fr
ont
panel Min, Mid, Max V
olume LEDs) between adjustments to the audio input levels. For details on making these adjustments via th
e fr
ont panel contr
ols, see chapter thr
ee.
V
iew
Signal,
Normal,
&
Clip
status
S
o
r 0
S
S
o
r 0
S
S
ig
X5
•Norm
X5
•Clp
X5
X5
= 0 (of
f) or 1 (on).
V
iew Signal (Min) status
1S
1S
X5
Signal detection threshold: 0 = of
f (Signal level is too low to detect.)
1 = on (A signal of at least -20 dBV [-18
dBu
] is pr
esent.)
V
iew Normal (Mid) status
2S
2S
X5
Normal range: 0 = of
f (Input level is too low
.)
1 = on (Input is in the right range.)
Command/r
esponse table for SIS commands (continued)
Command
ASCII
(T
elnet)
URL Encoded (W
eb)
Response
Additional description
(host to switcher)
(host to switcher)
(switcher to host)