Command and response table, For special function sis commands – Extron Electronics ISM 482 User Manual
Page 51
ISM 482 Integrated Scaling Matrix Switcher • Programming Guide
45
Command and Response Table for Special Function SIS Commands
The syntax for setting a special function is
X/*X?#
where
X/
is the value or variable (such as
35
in the first example below),
X/
is the function number (such as “set RGB delay” in the first
example below), and
#
is the execute command. To view the setting of a function, use
X?
#
where
X?
is the function number.
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
RGB delay
RGB delay (Triple-Action Switching)
X2)
*3#
Dly
X2)]
Switching delay of the selected input
to the preview output. Adjustable
in 0.01 second steps from
0
up to
50
= 5.0 seconds.
0
= 0.0 seconds
(default),
1
= 0.1 seconds,
2
= 0.2
seconds, and so on.
Example:
35*3#
Dly35
]
RGB delay set to 3.5 seconds.
Scaler output settings
Output sync format
X*
*6#
Syn
X*]
00
= RGBHV (
default)
01
= RGBS
Example:
1*6#
Syn1
]
RGBHV output signal.
Output polarity
X(
*7#
Pol
X(]
X(
: Horizontal/Vertical polarity
0
= H–/V–
2
= H+/V–
1
= H–/V+
3
= H+/V+
Example:
1*7#
Pol1
]
H–/V+ output polarity.
Blue screen
Blue screen
(blue & sync output only)
X#
*8#
Blu
X#]
0
= off (normal output).
1
= on (blue video and sync output).
Example:
1*8#
Blu1
]
Blue and sync output for setup.
Edge smoothing
Edge smoothing
X#
*16#
Fil
X#]
00
= off
01
= on (
default)
Example:
1*16#
Fil01
]
Enable edge smoothing.
Enhanced mode
Enhanced mode
X#
*12#
Enh
X#]
0
= off.
1
= on.
Example:
1*12#
Enh01
]
Enable enhanced mode.
Auto Image
Set Auto Image
X#
*13#
Img
X#]
00
= off
01
= on
Example:
1*13#
Img01
]
Set Auto Image on
.
Execute Auto Image
X1*
*14#
Img
X1*]
X1*
: Auto Image input tied to output:
Out 1/Out 2
Out 1/Out 2
01
= Yes/No
03
= Yes/Yes
02
= No/Yes
X@
Reconfig
]
Output
X@
Auto Image is complete.
X@
Reconfig
]
Output
X@
Auto Image is complete.
NOTES:
•
If Auto Image adjustments are not necessary for an input, the
X@
Reconfig
]
message may not be received.
•
If both outputs are receiving the same input, both outputs are auto imaged regardless of the
X1*
received.
PAL film mode
Set PAL film mode
X!
*
X#
*18#
X!
Flm
X#]
X#
:
0
= off (
default)
1
= on
Example:
8*1*18#
8Flm01
]
The ISM uses its 2:2 pulldown (PAL)
video processing algorithms to scale
input 8.
Read PAL film mode
X!
*18#
X#]
0
= off
1 = on.